31AE162-034 (2004) Ryobi Snow Blower - Overview

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

This is a Genuine OEM Approved replacement part designed for use with Snow Throwers. This part is made out of Rubber and it is Sold Individually. This part mounts with 2 Screws (Sold Separately) at each end. You would need a Wrench to replace this part • Remove the ignition key • Disconnect spark plug • Tilt Snowblower back so it...Read more rests on it's handles for support • Remove all 4 bolts on the auger paddle and then remove the paddle • Install the new auger paddle into the bracket on the auger shaft • Make sure that the auger paddles are secure

This genuine component is supplied directly from the original equipment manufacturer for use with Ryobi and MTD lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hex washer screw. Ke...Read moreep in mind this high-quality part is made of durable metal and is sold individually.

The Push Cap Rod is a 1/2-inch metal metal cap which can be easily installed with a hammer and pliers. This manufacturer certified part comes in silver and is made of metal. This cap attaches onto an axle to help the wheel stay attached. If broken, the wheel will fall off and the part should be replaced.

This is a genuine OEM sourced replacement part that is intended to be used with lawnmowers, snowthrowers, and tillers from Bolens, Ryobi, Yard Machines, MTD, Troy-Bilt, and Yard-Man. The sealed bearing is used to limit friction between a rotating shaft and a fixed part assembly. It is recommended to review your models illustrated part dia...Read moregram to confirm the bearing\\\'s compatibility. This item is sold as an individual replacement part.

This OEM Top Locknut measures 5/16x18, is made of metal, and it isused to secure parts in place and prevent backing out from vibration. Replacing this part varies in difficulty depending on the part it is securing and the equipment in question, but it is generally an easy job according to our customers. Installation requires a wrench or socket.

This part is an OEM sourced directly from the manufacturer for use in lawn tractors made by Ryobi, Yard Machines, MTD, Bolens, Yard Man, Troy-Bilt, Poulan, and Cub Cadet. The flat washer attaches to the bearing cup. When replacing this item a wrench might be required during the installation process. Over time this part may break or bend a...Read morend will need to be replaced. This item is made out of metal and is available individually.

This is an original Craftsman replacement part. The carriage screw is designed by the manufacturer for use in snowblowers and lawn tractors. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to the parts diagr...Read moream to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

This is an original MTD, Yard-Man, Troy-Bilt, Bolens and Yard Machines part for use with Snow Blowers. The auger drive cable connects the auger control lever on the control panel to the engagement lever in the auger drive system. The most common reason for replacing the cable is when it is broken, causing the snowblower to not properly pi...Read moreck up snow. This part is sold individually. The tool that you will need to replace auger drive cable is a 3/8" socket.

It is an identical replacement for a missing or a damaged clamp that is used to secure the fuel hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Check the appropriate diagrams for your model for the correct location and application of this hardware. This is a genuine manufacturer-sourced part...Read more which is designed for use on lawn and garden equipment. Pliers might be needed to remove and secure this hose clamp.