This fuel tank assembly is supplied by the original manufacturer for use in trimmers. It is responsible for storing and transferring fuel to the engine for combustion. The assembly consists of a plastic tank, a fuel cap, a fuel filter, and the fuel lines which have a diameter of 0.25 inches. If the fuel tank is damaged, or the fuel lines ...Read moreare clogged, the assembly will need to be replaced. A faulty fuel tank assembly will result in fuel leakage, hard starting, rough idling, and poor equipment performance. To begin, drain the fuel from the tank. Disconnect the fuel lines and remove the mounting hardware that secures the assembly to the equipment. Pull off the old assembly and align the new one with the mounting holes. Secure the assembly in place and reconnect the fuel lines. Refill the fuel tank to complete the repair.
This genuine bump head knob assembly, sometimes known simply as the bump head, is black and approximately 2 inches long. Sold individually, this plastic part releases the cutting line. Over time, this part may break due to wear, and you will know it is broken because it will completely stop functioning.
A troubleshooting tip is to tap t...Read morehe part on theg round to see if the cutting line advances. This is an easy repair to make, and does not require any tools. You will need to look for the bump head attachment point on the bottom of the cutting head assembly.
The pawl assembly is a complete OEM kit that includes the two plastic pawls, the two springs, and the metal housing. Installation is rated "Medium" difficulty and requires a screwdriver and socket set. This part houses the pawls that will grap onto the flywheel when the rope is pulled to start the engine. This part attaches inside the rec...Read moreoil housing. If broken, You will not be able to start the engine. The rope will be loose. Inspect for damage, and replace if broken.
Fuel tanks are responsible for storing and supplying fuel, like gasoline, for an engine. This fuel tank assembly is designed for and compatible with various models of trimmers and includes the plastic fuel tank and fuel cap, securing screws, and 2 fuel lines. To best maintain your fuel tank, make sure to inspect the fuel filter regularly ...Read morefor any clogs that could affect equipment performance, and replace it when necessary. Over time and through aging, fuel tanks themselves can wear down and crack, or get severely clogged, leading to issues like contamination rendering the tank unsafe to use, and in need of replacement. You must drain the fuel from the tank before you replace it, and you will need a screwdriver or wrench to remove any panels and securing screws containing the tank.
This is a genuine OEM replacement part designed for use with some Handheld String Trimmers. This filter is made out of Foam and it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or d...Read moreirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with trimmers and blowers. The gasket is used to seal the connection between the carburetor and the air cleaner assembly. It is recommended to replace gaskets when servicing the motor to ensure proper seals when the parts are reassembled. This item is available as an individual replacement part.
This clutch assembly is a genuine OEM replacement kit for outdoor lawn equipment. The kit includes the clutch drum, clutch, clutch washer, and screw. The clutch assembly transfers power from the engine to the cutting attachment which allows you to operate the equipment. Over time, the clutch assembly may malfunction due to normal wear and...Read more tear or accidental damage. If the small clutch assembly fails, the engine will likely stall, and the cutting attachment will not be able to engage. To remove the clutch assembly, first bind the piston to prevent it from rotating. You can do this by removing the spark plug and inserting a length of rope into the cylinder with a few inches remaining outside. Remove the clutch cover and use a clutch removal tool to remove the nut that secures the assembly. Pull the old assembly from the crankshaft and position the new assembly in its place, ensuring it is securely fitted.
This plastic throttle trigger measures 2.5-inches in length and controls the power, speed, and intensity of the motor for your lawn equipment through the throttle cable and carburetor it is attached to. Sold as an individual part without any securing hardware, this trigger, although made of durable plastic, is a high-use part that will ne...Read moreed to be replaced more often than other parts. Check the user manual for your model for exact placement and installation location of this trigger.
This is a manufacturer approved O-Ring designed for lawn and garden equipment. This is the O-Ring that provides an Air Tight seal between Carburetor and Cylinder Head. If doing maintenance on carburetor it is recommended to replace the O-Ring instead of re-using the old one. Over time rings and seals tend to dry out and would no longer provide proper seal compromising engines performance.
This carburetor is supplied by the original manufacturer as a replacement part for gas trimmers. It is made up of a metal body and plastic choke lever. The carburetor is responsible for mixing air and fuel for combustion within the engine. Over time, it can fail due to various reasons such as blockage in the fuel connections, clogged jets...Read more, damaged float, a worn-out needle valve, or a faulty gasket. A faulty carburetor will result in poor idling, difficulty starting, loss of power, stalling, and misfires. Before beginning any repairs on the carburetor, drain the fuel from the fuel tank and disconnect the fuel lines. Remove the air filter assembly and disconnect all other attachments that secure the carburetor to the engine. Remove the mounting fasteners that hold the carburetor and carefully pull it off the engine. Inspect the carburetor gasket and replace it as well if it is no longer providing an adequate seal. Place the new carburetor in position and reinstall the mounting fasteners to keep it in place. Reassemble the equipment in reverse order to complete the repair.
This spool is for line trimmers.
Spool houses the cutting line and fits inside the cutting head to cut grass and weeds.
Wear work gloves to protect your hands when installing this part.
This air filter is an original sourced directly from Craftsman. The filters purpose is to keep dirt, dust and other contaminants from entering the carburetor and engine. You can clean this foam filter by putting it in a clean plastic bag with a little oil and rub the oil into the filter, then remove the filter and squeeze it in a paper towel to remove the excess oil. This is an individually sold part.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fuel line broke
13 of 16 peoplefound this instruction helpful.
Erik from ROBERTSDALE, AL
Really Easy
15 - 30 mins
Screw drivers
Removed the two screws holding the fuel tank to the main unit. Removed the two fuel lines and any stuck on rubber. Installed and installed two screws to mount the new tank. Slid fuel lines on their respective connectors. Done.
Was this helpful?
Thank you for voting!
Air Filter needed to be changed
5 of 8 peoplefound this instruction helpful.
Arthur from LAVONIA, GA
Really Easy
Less than 15 mins
Air filter has a tab to open cover just press the tab to remove take old filter out and replace it with new one then reinstall the cover and you're done.
Was this helpful?
Thank you for voting!
Replace Starter Housing with broken pull cord.
2 of 2 peoplefound this instruction helpful.
Timothy from GAINESBORO, TN
Really Easy
30 - 60 mins
Wrench (Adjustable)
1. Remove Shaft & clutch cover by removing 3 torx screws and loosening cinch bolt.
2. Remove clutch assembly with torx tool in center and then by cinching the shaft and turning spring assembly counter clockwise with an adjustable wrench.
3. Remove starter housing by removing 3 Torx bolts from the front and a screw
... Read more from the back.