30859N Toro - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This oil seal is an OEM replacement part designed to prevent oil from leaking from the engine or gearbox while keeping contaminants from entering. It is used in various lawn mowers where it ensures that the moving parts in the mower remain adequately lubricated and protected from dirt/debris. The oil seal can wear down due to aging, heat,...Read more pressure, or improper installation. If the seal is no longer functioning oil will leak, the engine will overheat, and its internal components will wear down due to excessive friction. Use seal pullers to remove the seal from its housing on the engine crankshaft or transmission housing. Clean the surrounding area using a cloth or soft brush to prevent contamination and ensure a good seal. Apply oil to the lip of the new seal and firmly press into position until it is flush against the sealing surface. Once you have completed the repair, run the lawn mower to check that there are no longer any leakage or performance issues.

This 1/4-20 x 3/4-inch hex-head screw secures parts on compatible outdoor power equipment. It is made from Grade 5 steel and has a yellow zinc finish for added rust resistance. Check the equipment model and parts diagram before ordering.

This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this hig...Read moreh-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

The flat washer is an OEM replacement part that provides a wide surface area to distribute the load of a bolt or a screw when it is installed. This protects the part being fastened from getting damaged or deformed and provides a more secure fit for the bolt/screw. This flat washer is made of steel and has a diameter of 0.375 inches and a ...Read morethickness of approximately 0.063 inches. To replace the flat washer, first unthread the bolt/screw before using a flathead screwdriver to carefully pry it off. Clean the area, place the new flat washer in position, and thread the bolt/screw back on. Sold individually.

The lock washer goes next to the flat washer and is made of metal. It is available as an individual replacement part. This genuine item is supplied by the original equipment manufacturer for use with snowblowers made by Toro and Lawn Boy. A wrench might be helpful during the installation of this part. This item may become broken and will need to be replaced.

The Nut-Flange, Ni, simply known as a Flange Nut, is a silver metal individually sold part which can be applied with a wrench or socket and torque wrench. Simply torque the part to the manufacturer specifications. It is used to secure the idler arm assembly to the frame, and will need to be replaced if damaged. You can tell if it is brok...Read moreen if there are signs of visible damage, or the part won't tighten all the way due to damaged threads. Customers rated this repair as easy.

It is a genuine OEM sourced replacement part which is specially designed for use with Toro snowblowers. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.

It is made of metal and is sold individually. The screw connects to the idler pulley. A socket set might be needed during the installation process. Over time this part may become stripped and will need to be replaced. This part is an OEM from Toro and Lawn Boy for use in snowthrowers, tillers, blower-vacuums, and lawn tractors.