This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges.
Customers found this to be an easy repair.
This OEM hex nut secures the blower impeller assembly to the motor drive shaft. This part is black, made out of metal, and is sold individually. Hex nut threads can become damaged, and ends can become rounded off over time. This is a symptom of fatigue and will require replacement. You will know this part is broken if the impeller is no l...Read moreonger able to spin with the drive shaft. There will be no airflow from the blower.
Most of our customers rated this as an easy repair, all you will need is a wrench or socket and torque wrench. When installing your new hex nut on the impeller blower, ensure your torque to the manufacturer specs when securing it to the drive shaft.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
This oil seal is an OEM replacement part designed to prevent oil from leaking from the engine or gearbox while keeping contaminants from entering. It is used in various lawn mowers where it ensures that the moving parts in the mower remain adequately lubricated and protected from dirt/debris. The oil seal can wear down due to aging, heat,...Read more pressure, or improper installation. If the seal is no longer functioning oil will leak, the engine will overheat, and its internal components will wear down due to excessive friction. Use seal pullers to remove the seal from its housing on the engine crankshaft or transmission housing. Clean the surrounding area using a cloth or soft brush to prevent contamination and ensure a good seal. Apply oil to the lip of the new seal and firmly press into position until it is flush against the sealing surface. Once you have completed the repair, run the lawn mower to check that there are no longer any leakage or performance issues.
This authentic manufacturer-sourced screw-taptite is made for use with Toro and Lawn-Boy lawn and garden equipment. It is an identical replacement for a missing or a damaged hardware that was installed on a new unit. Refer to the appropriate diagrams for your model to ensure the exact location and the correct application of this screw. It...Read more is made of durable metal and is sold as an individual item. A wrench will be needed to secure or remove it.
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
This 1/4-20 x 3/4-inch hex-head screw secures parts on compatible outdoor power equipment. It is made from Grade 5 steel and has a yellow zinc finish for added rust resistance. Check the equipment model and parts diagram before ordering.
This replacement screw is a high quality item commonly utilized on Toro snowthrowers. It is a genuine OEM supplied hardware which has multiple uses depending on the equipment. Please make sure to check appropriate diagrams for correct location and application of this screw. This hex washer head screw is sold individually and it will require a wrench to secure of remove it.
The Lock Nut is used to secure and lock parts in place. This is a gold, metal, individually sold part which can be installed with a wrench set, and socket set, and attaches onto various locations on a variety of equipment. If broken, damaged or worn, the part may be loose, and there may also be physical damage to the nut, at which time it...Read more should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this hig...Read moreh-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.
This carriage screw is a genuine manufacturer sourced replacement part. It is specially designed for use with Toro snowblowers. This screw is generally used to secure the scraper blade. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the screw and keeps it from t...Read moreurning when the nut is tightened. Please note, this screw is made out of metal and it is sold individually.