305S Shindaiwa Chainsaw - Overview

This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to install. It is attached inside of the cylinder head, and is used to ignite the air fuel mixture inside the combustion chamber. You can clean...Read more the spark plug with a fine sandpaper of 180 or more, then spray it with carburator cleaner and wipe dry. However, even after regular maintenance, spark plugs need to be changed as part of good engine fine-tuning. Regap to manufacturer specifications. Refer to your owners manual or model number to ensure you are choosing the correct product. Note: If your engine has more than one cylinder and sounds like it has a miss, you can remove each spark plug wire one at a time to find the miss. If the engine drops in rpm when you remove the wire, then that cylinder is fine, if it does not drop then you have found your miss!

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

This OEM replacement part is used to pump fuel from the tank to the carburetor in order to start the engine. It may also be referred to as a Primer Bulb. It is made of durable black plastic and is sold individually. This part will be found in various locations, depending on your model; refer to your owners manual to locate it on your mach...Read moreine, but is commonly found on the side of the air cleaner or carburetor. To complete this repair, you will need a screwdriver. The Purge Bulb needs to be replaced when it is cracked or damaged. It will become fatigued through regular use and may leak fuel when it is malfunctioning. Customers rated this repair as Easy.

This flanged hex nut is a genuine OEM steel fastener specifically designed for use in chainsaws and chop saws, serving the purpose of securing various components in these outdoor power equipment devices. It features a flange base that acts as a built-in washer for extra stability and security. The hex nut has a diameter of 6mm, and its th...Read morereaded shaft has a pitch of 20, ensuring a secure and reliable connection. Over time, the bolt can be susceptible to corrosion, cracks, or worn threads, which may result in the loosening or detachment of the connected parts. Detectable signs of such issues include excessive noise, vibrations, and equipment instability. To address this, it is recommended to inspect all bolts within your equipment and replace any that are no longer functioning properly. To replace the bolt, simply use a wrench or socket to loosen and remove the old one, position the new bolt on the mounting surface, and securely tighten it until the flange is flush against the surface. Please note that each flanged hex nut is sold individually.

Genuine OEM replacement part, this part is sold individually. The Bevel Gear is part of the chain tensioning assembly of the chainsaws listed below. This part aid in loosening and tightening the chain on the chain bar.

This is a genuine manufacturer approved replacement part designed for use with chainsaws. This part is an essential part of chain tensioner mechanism. When replacing this part you will need a screwdriver. It is made out of metal and it is sold individually.

This is a genuine Echo replacement part that has been sourced from the original manufacturer and is intended to be used with chainsaws. The metal stub is threaded on two ends, one end threads into the chassis and supports the guide bar plate, the bar, and cover. The chain bar bolts secure the outer end of the guide bar studs. This stud is priced as a single item, please note two may be required.

This is an Authentic Part sourced from Original Manufacturer designed for use with some Echo Chainsaws. This part is made out of Metal and it is Sold Individually. If the chainsaw bar doesn't adjust usually the tension Chainsaw Chain Adjustment Bolt is worn or damaged.

This is an Authentic Part sourced from Original Manufacturer. This part is made out of Metal and it is Sold Individually. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged.

This replacement oil cap is specially manufactured for Echo and Shindaiwa chainsaws. It is an authentic OEM part, not an aftermarket equivalent. It is used to keep the oil in the tank. This assembly includes a retainer that remains in the tank to prevent the cap from falling out. It is made out of strong plastic material and it is sold individually.

This spark plug is a genuine OEM part that is used on gas-powered lawn and garden equipment. The spark plug creates the spark that ignites the fuel and air mixture inside the engine, allowing it to run. It comes in a cylindrical shape with a ceramic insulator and a metal electrode that protrudes from the top. If your spark plug is faulty,...Read more your small engine may misfire, have difficulty starting, consume more fuel or not start at all. To check that the spark plug is faulty, you will need to use a spark tester to test it for electrical failure. Once you have done so, you can remove the faulty spark plug using a spark plug socket and ratchet. Place the new spark plug in to the socket and use your hands to carefully thread it into the engine. It is important to note that you should not wait until your spark plug is faulty to replace it. It should be replaced regularly as part of your annual small engine maintenance.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.