My Orders
3037-09 (Type 2) Black and Decker Circular Saw - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Longer Available
Ball Bearing
Part #330003-16
$6.40
Special Order
SCREW
Part #055206-00
$6.40
Special Order
Screw
Part #099248-14
No Longer Available
Screw
Part #70907-00
$6.40
In Stock
Spring
Part #058287-00
This extension spring is sourced directly from the original equipment manufacturer for Black and Decker and DeWALT drill presses. It is an important component that applies tension on the knob for the edge guide. Over time it may wear out and lose tension eventually requiring a replacement. To ensure the correct installation of this hardwa...Read morere, check the diagrams of your specific model. This high-quality spring is made of a durable metal and is sold as an individual item. Replacing it does not require any tools, remove the knob and replace the spring.
Read less
No Longer Available
Brush and Spring
Part #72030-00
No Longer Available
Ball Bearing (6202)
Part #330003-13
$6.40
Special Order
O Ring
Part #701297-00
O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness.
There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are:
• Extrusion and Nibbling...Read moreu> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps.
• Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication.
• Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat.
• Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity.
• Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.
Read less
$6.40
Special Order
Plug
Part #87205-00
This manufacturer-sourced item is specially designed for use with DeWALT and Black and Decker saws. It is an identical replacement for a missing or damaged plug that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep i...Read moren mind this high-quality item is made of durable material and is sold individually.
Read less
No Longer Available
Ball Bearing
Part #330003-04
Genuine Manufacturer Sourced replacement part used on a variety of Power Tools. This part is made out of Metal and it is sold individually. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces frictio...Read moren. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. Included in part number 605511-00
Read less
$6.40
Special Order
Washer
Part #417-00
$6.40
In Stock
Terminal
Part #683784
The terminal is made out of metal. This item is available as an individual replacement part. It is a genuine DeWALT, Black & Decker, and Porter Cable part sourced directly from the manufacturer for use in saws, drills, engines, grinders, nibblers, routers, sanders, and shears. A set of pliers may be required to replace this item. This part may become broken and will need to be replaced.