3025 - Overview

This part is the replacement chain for your pole saw. It is made of metal and is sold individually. The chain rotates around the bar to help the pole saw cut properly. If the chain is damaged or missing teeth, it may not cut evenly, or at all, and will need to be replaced. This is an authentic OEM part sourced directly from the manufacturer.

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 3290875G Retaining Ring is to attach and hold the washer and sprocket to the driveshaft on the models shown below. To remove this part it is best to use retaining ring pliers (or snap ring pliers).

This is a genuine OEM replacement part, it is sold individually. The purpose of this washer is to act as a spacer between the chain sprocket and as a friction barrier on the chainsaw models shown below. This is a wear part that we send out quite often. It is advised to order an extra one or two to keep on hand.

This is a Genuine Manufacturer Approved replacement kit used on certain Electric Pole Saws. This kit includes all metal parts: Adjustment Screw, Retaining Pin, Adjustment Bar/Plate. Chainsaw chains stretch and become loose during operation. Saw chain tension should be checked and tightened often. If the chain is too tight, not only will i...Read moret rob the saw's engine of power due to increased friction, but the chain also runs the risk of breaking. If the chain is too loose, it can come off the bar and seriously injure the operator.

Genuine Craftsman replacement part, this item is sold individually. Chainsaws use sprockets to engage and spin the chain. When it wears down, your saw will see a sharp decrease in performance. A worn sprocket may cause the chain to slip or not spin at all, and when this happens, you will want to replace it.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This replacement oil filter is specially designed for use with Kawasaki engines. It is a genuine OEM sourced part, not an aftermarket immitation. This oil filter is used to remove contaminants from the engine oil. This part is manufactured in accordance with applicable EPA emissions regulations. It is recommended to replace oil filters at...Read more least once a season. Please note, this item is sold individually. To replace the oil filter you will need a pipe wrench or a filter wrench. • Disconnect the spark plug • Remove the old oil filter by twisting it counterclockwise • Clean the sealing surface on the oil filter adapter from any dirt or debris • Lightly oil the filter gasket with clean engine oil • Install the new filter

This is a genuine OEM replacement part used with many 4 stroke engines. The Kawasaki gasket secures the float to the float chamber. This rubber component is sold individually. A wrench, pair of pliers and a screwdriver are needed for the removal and replacement.

This is a genuine replacement part manufactured for use with outdoor power equipment. This flanged hex head screw has several applications, please see model diagram for part use and location. This screw is available as an individual replacement part.