30188 Toro - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This short-style engine oil filter is designed to remove harmful contaminants from the oil while maintaining proper lubrication in pressure-lubricated small engines. Built with high-efficiency filtration media and internal safety features to support consistent oil flow, it helps reduce engine wear and protect internal components. Ideal fo...Read morer routine maintenance, it supports reliable performance and helps extend engine life during regular operation.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This is an authentic OEM component from Briggs & Stratton. The cylinder head gasket is compatible with many small engines, and is sold individually. The cardboard composite gasket is fitted onto the cylinder head, providing protection from friction and leaks. A wrench is needed for the repair. This item is also included with the valve gasket set (808392).

The Lock Nut is used to secure and lock parts in place. This is a gold, metal, individually sold part which can be installed with a wrench set, and socket set, and attaches onto various locations on a variety of equipment. If broken, damaged or worn, the part may be loose, and there may also be physical damage to the nut, at which time it...Read more should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.

The flat washer is an OEM replacement part that provides a wide surface area to distribute the load of a bolt or a screw when it is installed. This protects the part being fastened from getting damaged or deformed and provides a more secure fit for the bolt/screw. This flat washer is made of steel and has a diameter of 0.375 inches and a ...Read morethickness of approximately 0.063 inches. To replace the flat washer, first unthread the bolt/screw before using a flathead screwdriver to carefully pry it off. Clean the area, place the new flat washer in position, and thread the bolt/screw back on. Sold individually.

The valve tappet attaches to the push rod. It is made out of metal and is sold individually. This is a Briggs & Stratton and Toro replacement part directly sourced from the manufacturer for use in engines. It may require a set of pliers during installation. This part may become broken and will need to be replaced.

This is an authentic replacement part manufactured for use with Toro snowthrowers. The ni lock nut is designed to prevent from being unthreaded from vibration. This nut is used with several different models of snowthrowers and is used with various applications. The nut is sold as an individual replacement part, please see model diagram for associative parts.

It is an authentic OEM sourced part which is specially made for use with Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is an identical replacement for a faulty or a missing spark plug wrench that was included with a new unit. The wrench allows a user to secure or remove a spark plug. Refer ...Read moreto the appropriate diagrams for your model to ensure the exact location and the correct application of this component. A screwdriver will be needed to secure or remove this part. This high-quality part is made of durable metal and is sold as an individual item. Note. This spark plug wrench fits 5/8" and 13/16" spark plugs.

The lock washer goes next to the flat washer and is made of metal. It is available as an individual replacement part. This genuine item is supplied by the original equipment manufacturer for use with snowblowers made by Toro and Lawn Boy. A wrench might be helpful during the installation of this part. This item may become broken and will need to be replaced.