30175 Toro - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This is a genuine manufacturer supplied replacement fuel filter. It is specially produced for use with Toro snowthrowers. This is a plastic fuel filter that is sold individually. Its purpose is to filter out any contaminants from the fuel before it goes into the engine. It will over time get clogged and restrict the fuel from getting to t...Read morehe engine. To replace this filter you should only need pliers to remove and install the clamps that secure fuel lines.

This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.

It is an OEM item that is made for use with Kohler engines commonly installed on a variety of lawn and garden equipment. This is the valve that the push rod ride inside of which will push the exhaust valve open during the exhaust stroke. A bent push rod or a damaged lifter-valve can not only affect your engine\\\'s performance, they can s...Read moreeriously damage other parts if the problem is not taken care of immediately. This is a high-quality replacement for a missing or a damaged component that was installed on a new unit. To ensure the correct location and installation of this item, refer to the diagrams of your specific model. Note, one durable metal lifter-valve and a tube of lube are included. You will need a screwdriver and a wrench set to take apart the engine when performing this repair.

The lock washer goes next to the flat washer and is made of metal. It is available as an individual replacement part. This genuine item is supplied by the original equipment manufacturer for use with snowblowers made by Toro and Lawn Boy. A wrench might be helpful during the installation of this part. This item may become broken and will need to be replaced.

It is made of metal and is sold individually. The screw connects to the idler pulley. A socket set might be needed during the installation process. Over time this part may become stripped and will need to be replaced. This part is an OEM from Toro and Lawn Boy for use in snowthrowers, tillers, blower-vacuums, and lawn tractors.

This replacement hardware is sourced from original equipment manufacturer for use with Toro snowthrowers. It is standard hardware which has multiple applications, please refer to appropriate diagrams for correct location and use of this locknut. This part is made from durable metal and it is sold individually.

This is a genuine Toro replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal flat washer is used to disperse pressure put on a part assembly by a nut or bolt across a wider surface area. This item is used with several different models of snowthrowers. It is recommended to review your...Read more model\\\'s part diagram to confirm the washer\\\'s compatibility and usage. The flat washer is priced individually.

The screw is made of metal and attaches to the front panel. This is a genuine Toro and Lawn Boy part sourced directly from the manufacturer for use in snowblowers. Keep in mind that this item is sold individually. When replacing this part a flat head screwdriver might be required during the installation process. It might strip or break over time and will need replacing.