30166 Toro - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.

This is a genuine OEM replacement part used with many 4 stroke engines. The Kawasaki gasket secures the float to the float chamber. This rubber component is sold individually. A wrench, pair of pliers and a screwdriver are needed for the removal and replacement.

This O-ring, also known as a round seal, is an authentic OEM part used in lawn and garden equipment. It is a small, circular, rubber ring that helps create an airtight seal between the oil filter filler and engine to prevent leaking and ensure adequate lubrication. It is common for the O-ring to become brittle and lose its elasticity due ...Read moreto aging, and exposure to chemicals and high temperatures in the equipment. If an O-ring fails, it can result in oil leakage, leading to reduced equipment performance, and potential damage to the surrounding components. Carefully the oil ring off the sealing surface and clean the area thoroughly to ensure a proper seal for the new O-ring. Lightly lubricate the new O-ring and press it on to the sealing surface.

This is a genuine manufacturer supplied replacement fuel filter. It is specially produced for use with Toro snowthrowers. This is a plastic fuel filter that is sold individually. Its purpose is to filter out any contaminants from the fuel before it goes into the engine. It will over time get clogged and restrict the fuel from getting to t...Read morehe engine. To replace this filter you should only need pliers to remove and install the clamps that secure fuel lines.

The Lock Nut is used to secure and lock parts in place. This is a gold, metal, individually sold part which can be installed with a wrench set, and socket set, and attaches onto various locations on a variety of equipment. If broken, damaged or worn, the part may be loose, and there may also be physical damage to the nut, at which time it...Read more should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.

This replacement carburetor gasket is a high quality item designed for use on Kawasaki engines commonly installed on Toro lawn and garden equipment. It is an authentic part that is sourced directly from original equipment manufacturer to provide and air tight seal between the carburetor and the insulator. Please note one compound material gasket is included per order.

The lock washer goes next to the flat washer and is made of metal. It is available as an individual replacement part. This genuine item is supplied by the original equipment manufacturer for use with snowblowers made by Toro and Lawn Boy. A wrench might be helpful during the installation of this part. This item may become broken and will need to be replaced.

This replacement hardware is sourced from original equipment manufacturer for use with Toro snowthrowers. It is standard hardware which has multiple applications, please refer to appropriate diagrams for correct location and use of this locknut. This part is made from durable metal and it is sold individually.

This is a genuine Toro replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal flat washer is used to disperse pressure put on a part assembly by a nut or bolt across a wider surface area. This item is used with several different models of snowthrowers. It is recommended to review your...Read more model\\\'s part diagram to confirm the washer\\\'s compatibility and usage. The flat washer is priced individually.