3000VT Makita Saw - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This is an authentic OEM sourced replacement part designed for use with Makita reciprocating saws. This part helps securing the sleeve inside the tool. This part is made out of plastic and it is sold individually.

This is a genuine manufacturer sourced replacement part designed for use with Makita reciprocating saws. This sleeve fits the driving assembly in the tool. It is made out of plastic and it is sold individually. Please note the pin used to secure this sleeve is sold separately.

This part is an OEM sourced directly from the manufacturer for use in Makita reciprocating saws. The push pin goes between the compression spring and the blade clamp. It is a very small part and will to be replaced if it gets lost or if it breaks. A screwdriver may be necessary when replacing this metal part. The pin is available as an individual replacement.

This is a genuine OEM replacement part used on Makita reciprocating saws. It is made out of metal and it is sold individually. It is an important part of keyless blade clamp allowing for quick blade change. To replace it you may need a screwdriver and pliers.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This compression spring is a genuine OEM replacement component designed to maintain proper tension and support smooth internal operation across a variety of power tools. Made from durable spring steel, it helps ensure consistent movement within mechanisms such as levers, guides, or trigger systems, contributing to stable performance and r...Read moreeliable tool function. Replacing a worn or weakened spring helps restore proper pressure, improve responsiveness, and maintain overall efficiency during regular use.

This replacement tapping screw is an authentic item that is supplied by the original manufacturer for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this part. This high-quality phillips pan-head screw is made of durable metal and it is sold individually.

This replacement pin is an authentic OEM component which is made for use with Makita equipment. The pin is generally utilized to secure a part while allowing it to rotate freely. It is a standard hardware which may have multiple applications. Make sure to refer to the appropriate diagrams of your model for the exact location and the corre...Read morect installation of this pin. One durable metal item is included. You may need a screwdriver to take the unit apart when replacing this pin.

This genuine OEM steel ball is found within the housing of your power tool. It serves as a detent mechanism, securing the shift knob in various positions to allow for the selection of different operating modes. It has a diameter of 4.8mm. If you notice signs of wear or deformation on the steel ball, it is a clear indication that it needs ...Read moreto be replaced. A worn-out steel ball can result in a loose shift knob that fails to hold its selected position properly. To locate and access the steel ball within the housing, refer to the instructions outlined in your user manual. Your tool may use steel balls of different sizes, so confirm that this is the correct part your repair will need before making your purchase.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.