My Orders
3-RACK Maytag Dishwasher - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$10.70
In Stock
Lower Wheel Assembly
Part #WP99002780
This lower dishrack roller is less than two inches in diameter. It is made entirely of white plastic. If you find that your dishwasher is making loud noises or the lower rack is getting stuck when you are moving it in or out, it could be that the lower wheel assembly needs to be replaced. The dishrack wheels allow for easy movement of the...Read more dishrack in and out of the dishwasher. These rollers tend to wear down at the same speed, so it is recommended to replace both pairs at the same time. Open your dishwasher and remove the bottom rack, locate the locking tab, and rotate until it easily slides out of place. Slide the new wheel over the shaft and locate the locking tab to snap back into place.
Read less
$9.62
Special Order
Dishrack Tine Pivot
Part #WP99002735
This fold away tine pivot is almost four inches long. It is blue in color and is made of plastic.
$44.23
In Stock
Silverware Basket - Split/Fit
Part #6-918651
This is now one complete basket instead of being sold in 2 halves.
$9.62
In Stock
Fold Away Tine Pivot
Part #WP99002709
The fold away tine pivot or clip holds the tine rows in place. This part is made of gray plastic and is approximately 3 and a half inches in length. Some dishwasher models will have fold away tine rows, so you can easily accommodate larger items. The fold away tine pivot can be disconnected to fold down these tines. If the pivot is damage...Read mored or missing, the tines will not remain upright when they are returned to that position. Most dishwasher models will have two tine pivots per rack. However, this product is sold individually.
Read less
$142.08
In Stock
Dishwasher Accumulator Filter
Part #WPW10192799
This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.
$51.61
In Stock
Dishwasher Wash Impeller
Part #WP99002659
This dishwasher wash impeller assembly is a key component that helps circulate water and detergent through the spray arms during each cycle. Made from durable, multi-finned plastic, it attaches to the motor shaft and spins to ensure thorough cleaning throughout the tub. If your dishwasher is leaving dishes dirty, making unusual noises, or...Read more leaking, a worn or damaged impeller may be the cause. Replacing it can restore proper water flow and improve overall performance.
Read less
No Longer Available
Fold Away Tine Latch
Part #99003190
No Longer Available
Seal and Chopper Kit
Part #WP6-919539
THE COURSE THREADED SLEEVE IS NLA SO THE KIT SHOULD NOW ONLY HAVE 1 SLEEVE 07/18KC UPGRADE TO NEW MOTOR WHICH CONTAINS SHAFT W10118627 1/14KC
$9.62
Special Order
$9.62
In Stock
Wash Arm Cap
Part #WP99002654
This part is the replacement wash arm cap, also known as the spray arm nut, for your dishwasher. It is made of white plastic and is approximately ½ an inch in diameter. The wash arm cap fastens the lower spray arm to the pump housing. If the arm cap is damaged or missing, the arm can wobble or fall off during operation, and this can make ...Read moreit extremely difficult to wash your dishes effectively. To replace the wash arm cap, simply remove it from the spray arm, and replace it with the new cap. This part is an authentic OEM part from the manufacturer, and is sold individually.
Read less
No Longer Available
Dishwasher Lower Spray Arm Shield Included
Part #WP6-917642
This spray arm is located on the lower half of your dishwasher. Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack.
No Longer Available
Docking Station with Flappers
Part #WP6-917647
If you notice that your dishwasher is leaking, or is not cleaning dishes properly, you may need to replace the docking station. The docking station is located on the water supply tube at the back of the appliance. It provides water to the upper and middle spray arm. This part comes with the accompanying flappers. This product is approxima...Read moretely 4 inches in length and 2 inches in width, and is made of white and gray plastic. To access the docking station, you will need to remove the upper rack. To do this, simply remove the end caps that keep the rack on the slides. Make sure to attach the flappers to the docking station before installing it in the dishwasher.
Read less
Common Symptoms of the 3-RACK
How this model fails, and the parts that fix it.
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken silverware basket
100 of 110 people
found this instruction helpful.
the only thing that I wish was that the website had been more descriptive of the item. I ordered the two listed because it didn't say whether it was one side or both sides of a split basket. Now I have two complete baskets in different shades of grey! Only needed to order one maybe this will help someone else with the same problem. Gr
... Read more
eat service and fast delivery though! Will order from this site again if I ever need anything else!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Would not spray.
30 of 42 people
found this instruction helpful.
Looks like Maytag knew this was a problem. My chopper sleeve (plastic) was stripped and causing the impeller to not spin. The replacement part was all metal and was very easy to replace the old one just by removing screws. The replacement looks to be very sturdy and should last a lot longer than the original. Thanks.
Other Parts Used:
Was this helpful?
Thank you for voting!