2918H Simplicity Lawn Mower - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer'...Read mores specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.

This short-style engine oil filter is designed to remove harmful contaminants from the oil while maintaining proper lubrication in pressure-lubricated small engines. Built with high-efficiency filtration media and internal safety features to support consistent oil flow, it helps reduce engine wear and protect internal components. Ideal fo...Read morer routine maintenance, it supports reliable performance and helps extend engine life during regular operation.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.

Designed for use in Snapper and Simplicity ride-on mowers, this Roller is sourced directly from the manufacturer, is made of durable black plastic, is 4 inches long, and sold individually. The Roller helps allow the deck to move over the lawn without gouging into the ground. When the Roller has broken, you will notice the deck starts to...Read more ground out. This part will wear over time and needs to be replaced if it is damaged or fatigued. Customers rate the difficulty of this repair as Medium.

It is an OEM item which is made for use with Murray, Snapper, and Simplicity lawn mowers. This gasket provides a tight seal for the arbor housing. Over time the material will wear out and it may get compressed eventually requiring a replacement to ensure the unit functions properly. Refer to the specific diagrams of your model for the exa...Read morect location and the correct installation of the new part. It is a high-quality gasket which is made of a durable foam material and is sold as an individual component. You will need a wrench set to take apart the housing and gain access when replacing this gasket.

This is a genuine OEM sourced replacement air cleaner cartridge commonly utilized on Briggs and Stratton engines. It installed to filter our dust and other contaminants from entering carburetor and the engine. Please note, this pleated paper filter is sold individually. Keep in mind that the foam pre-cleaner is sold separately. Replacing...Read more this air cleaner cartridge is a simple task that should only require a wrench. • Remove the cover • Remove the old cartridge • Secure the new one in place • Secure the cover

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.

This is an authentic Briggs & Stratton replacement part sourced from the original manufacturer for use with small engines. The special screw includes a washer and is commonly used to secure the engine's exhaust manifold. The screw is available as an individual replacement part.