288707-1236-99 Briggs and Stratton Engine - Overview

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Metal, it is Sold Individually.

The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part. If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out. When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.

This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This is a genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. The needle valve opens and closes to control the flow of fuel into the carburetor. It is made out of metal and it is sold individually. You would need a screwdriver and pliers to complete this repair.