My Orders
287776-1237-E1 Briggs and Stratton Engine - Overview
Diagrams for 287776-1237-E1
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$6.40
In Stock
Starter Pawl-Ratchet
Part #281505S
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will have a hard time engaging the fly wheel, making the engine harder to start, and should be replaced. Installation is rated as "Easy" by cust...Read moreomers, and will require a screwdriver, pliers and nutdriver. Refer to your make, model and diagram to ensure this is the correct part for you.This model is plastic and comes in white.
Read less
No Longer Available
Gasket-rocker Cover
Part #272475S
This OEM Gasket Rocker Cover, which can also be called the Valve Cover Gasket, is used to provide a seal between the valve cover and engine. This is a gray-colored part, measuring 5 1/2 x 4 Inch, and it is sold individually. It can be attached using a wrench or socket. Note: this part also requires a Torque Wrench. When installing, tighte...Read moren and torque in alternating patterns, following the manufacturer specficiations.
You will know when it needs to be replaced when there is oil leaking around the valver cover gasket, which is a sign the part is broken, likely due to simple wear and tear or constant dryness. To make sure you are purchasing the right part, check your model number.
Customers rated this repair as easy.
Read less
$6.40
In Stock
Engine Filter
Part #298090S
This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.
Read less
$8.09
In Stock
Engine Oil Seal
Part #391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.
Read less
$9.08
In Stock
Connector-hose
Part #692317
This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Metal, it is Sold Individually.
$43.34
In Stock
Fan-flywheel
Part #796201
This is a genuine OEM sourced replacement part flywheel fan. It is specially manufactured for use with Briggs and Stratton engines that are installed on lawn and garden equipment. This fan is attached to the fly wheel and it will help to keep the engine cool for optimum performance. This blower fan is made out of plastic and it is sold in...Read moredividually. Please note the bolt used to secure this fan is sold separately. To complete this repair you will need a screwdriver and a wrench.
Read less
$6.47
In Stock
Gasket-exhaust
Part #692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.
Read less
$6.40
In Stock
Filter Fuel Mega Pack
Part #394358B
This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer'...Read mores specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.
Read less
$6.40
In Stock
Seal-o Ring
Part #691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part.
If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out.
When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.
Read less
$19.42
In Stock
Pulley-starter
Part #295871
Difficulty pulling the starter rope or a cord that stays extended can result from a damaged recoil pulley. This wheel guides and stores the rope while helping turn the engine during starting. Similar symptoms can come from a frayed rope, seized engine, bent starter housing, broken pawls, or weak return spring, so check those items first. ...Read moreMatch the replacement to the full engine model, type, code, and equipment model. Work on a cool engine with the spark plug lead removed. Release spring tension slowly and keep your face and hands clear of the starter housing. Route the rope correctly, confirm smooth return, and reinstall every guard before starting the engine.
Read less
No Longer Available
Spring-rewind Str
Part #490179
This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually.
Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy.
Locate and replace the start spring inside the starter housing; no special tools are required for this job.
Read less
$6.40
In Stock
Key-flywheel
Part #222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.
Common Symptoms of the 287776-1237-E1
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stopped running. Turned to be a bent intake push rod and broken rocker arm
9 of 15 people
found this instruction helpful.
Removed head. Replaced both rocker arms, intake pus rod, push rod guide exhaust and head gaskets. Torqued head in 3 stages to 216 in/lbs. gapped intake to .004 and exhaust to .006 at TDC
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!