285 (F013028501) Dremel Multi-Tool - Overview

• A slim, aluminum tube that provides the optimal grip for holding a bit in a Dremel rotary tool. • The collet features small identification rings around its shank. These rings correspond with the size of the collet: 0 rings = 1/8", 3 rings = 3/32", 2 rings = 1/16", 1 ring = 1/32" • Collets are compatible with 225 Flex-Shaft attachment. •...Read more For use with all rotary tools except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280.

This is a Genuine Manufacturer Approved replacement part used on some Dremel Rotary Multi-Tools. This part provides the firm grip for holding a bit in a tool. This Collet is for using bits with 1/8" arbors. Due to prolonged, heavy use a collet may need to be replaced. Collet Nut is sold separately.

This is the lock pin assembly for various dremel and multi-tool models. The lock pin is a crucial component within power tools, responsible for securing the bits in place during use to prevent any movement. Over time, lock pins can wear down or become damaged, leading to improper engagement or hindering the rotation and functionality of t...Read morehe tool. Replacing a lock pin involves turning off the dremel or multi-tool and removing its motor brushes and housing screws that hold it together. Separate the housing into two halves, take out the motor, and locate the lock pin. Remove the lock pin and its spring, then install the new lock pin and spring. Reinstall the motor, the other half of the housing, along with its screws and bushings.

An authentic OEM sourced item that is supplied for use with Dremel power tools. This special ring helps to provide a seal for the armature, make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable rubber and is sold i...Read morendividually, over time the material may wear out and begin to crack eventually requiring a replacement.

Original OEM replacement Armature Assembly used on some Dremel Corded Multi-Tools. This item includes an Armature, Fan, Armature Bearing, Commutator End Bearing, and the fan with pulley. Remember to be especially careful of the armature fan when you remove it, because if you break it, you will have to replace the entire armature. Due to c...Read moreonstant contact with Carbon Brushes armature will eventually wear out and would need to be replaced. It is highly recommended to replace both Carbon Brushes when replacing an armature.

• A slim, aluminum tube that provides the optimal grip for holding a bit in a Dremel rotary tool. • The collet features small identification rings around its shank. These rings correspond with the size of the collet: 0 rings = 1/8", 3 rings = 3/32", 2 rings = 1/16", 1 ring = 1/32" • Collets are compatible with 225 Flex-Shaft attachment. •...Read more For use with all rotary tools except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280.

• A slim, aluminum tube that provides the optimal grip for holding a bit in a Dremel rotary tool. • The collet features small identification rings around its shank. These rings correspond with the size of the collet: 0 rings = 1/8", 3 rings = 3/32", 2 rings = 1/16", 1 ring = 1/32" • Collets are compatible with 225 Flex-Shaft attachment. •...Read more For use with all rotary tools except discontinued Models 1, 2, and Series 1 or earlier of discontinued Models 260, 270 and 280.

This is an authentic manufacturer made replacement part which is specially designed for use with Craftsman variable speed rotaries. The caps covers and protects the motor brush on the motor brush holder. This part is made of durable plastic and is sold in a pack of two. For this repair, you will need a pair of needle nose pliers to aid you. Before starting this repair, be sure to unplug the unit from the wall.