2704X1 Makita Table Saw - Overview

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

Genuine Makita replacement part, this part is sold individually. This screw is used to secure various internal and external parts in the tool models shown below.It is a metric screw sized M4 X 16 (W, SW).

This is a genuine OEM sourced replacement part which is specially made for use with Makita saws. It is a standard hardware which has multiple applications, please make sure to check the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality tapping screw is made of durable metal and is sold individually.

This ring (15.8) is supplied directly from the original equipment manufacturer. The metal ring is designed to help secure the blade in the various miter saw devices. A screwdriver and a wrench are often necessary for the removal and replacement. The ring is sold individually.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Makita power tools. It is an identical replacement for a missing or damaged rubber pin that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicat...Read moreion of this hardware. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, table saws, masonry saws, planers, demolition hammers, and angle cutters. The washer has multiple applications based on the model of the power tool. It is recommended to review your model's diagram to verify this washer's compatibility. The washer is sold individually.

This pan head screw is an authentic replacement part. It is sourced directly from original equipment manufacturer for use with Makita power tools. This standard hardware is used in different locations depending on equipment. To ensure correct application please make sure to check appropriate diagrams. Includes one (1) metal screw. You will need a torx or a flat-head screwdriver to tighten or loosen this screw.