2610 Weed Eater Trimmer - Overview

The Fuel Cap with retainer, often simply known just as the fuel cap, keeps fuel from splashing out of your tank and debris from entering it. Black in color, it is sold individually and made of plastic. Because of everyday fatigue and wear, the cap can become damaged over time and must be replaced. You will know if it is time to replace ...Read moreyour fuel cap if you notice visible damage or experience fuel leaking from it. You can make this repair by hand, just attach the cap directly back onto the fuel tank. Most of our customers found this repair very easy.

This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.

The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Ref...Read moreer to your make, model and diagram to ensure this rope is right for your machine.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This metering diaphragm is an original part for use in edgers, blowers, trimmers, and chainsaws made by Poulan, Paramount, Weed Eater, Husqvarna, and Jonsered. It fits between the metering diaphragm gasket and the metering diaphragm cover. It is made of a thin material and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part and keep in mind that it is sold individually.

This fuel pump diaphragm, also called a membrane or a gasket, is what helps pump fuel from the tank to the engine of your gas-powered lawn equipment. It is normally found attached to the carburetor assembly itself. You can tell that the diaphragm is broken when your engine is not starting properly, lacks power, or frequently stalls. You m...Read moreay also notice that your machine is leaking fuel or smells strongly of gasoline. A broken diaphragm could lead to engine performance problems, and it may eventually stop working altogether. When replacing your old diaphragm, you will need a wrench to disconnect it from the fuel pump housing. Kindly note that this OEM-sourced component is sold individually.

This is an original replacement part manufactured for use with chainsaws and leaf blowers. The washer is commonly used to disperse the pressure put on the flywheel by a nut across a wider surface area. This washer is available as an individual replacement part, please see model diagram for associative parts.

This is a genuine Weed Eater, Poulan, Paramount, Husqvarna part for use with Trimmers. The cutting head assembly attaches to the drive shaft and houses the cutting line. This part is sold individually. The most common reason for replacing the trimmer head is if it is damaged. The tool that you will need to replace the line trimmer cutting head assembly is an Adjustable Wrench.

It is a genuine item that is supplied by the original equipment manufacturer for handheld lawn and garden equipment. The wrist pin retainer is an important component which helps to secure the piston pin. If the part is missing or is damaged, this will provide an identical replacement for the original component that was installed on a new ...Read moreunit. Note, this high-quality wrist pin retainer is made of durable metal and is sold as an individual item. Keep in mind, the pin is all sold separately. A screwdriver, a wrench set, and pliers will be needed to perform this repair. To ensure the correct replacement procedure, refer to the appropriate diagrams for your model.

This item is sold individually and helps the cutting head from getting damaged. The cover attaches to the tap button which attaches to the wound spool. The plastic cover will need to be replaced if it becomes broken and may require a screwdriver during the replacement. This is a genuine part from Weed Eater, Poulan, Husqvarna, and Jonsered for use in trimmers.