25372629017 Kenmore Refrigerator - Instructions

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair.

I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

Reviewed the video on your website and followed the directions to the letter. Great video

Really, really, really easy:
1.Unplug refrigerator (electrical safety).
2.Remove cardboard cover at bottom of refrigerator (two short self-tapping bolts) with a wrench.
3.Pull old fan blade off fan motor shaft (just held on by a compression fitting--no tools needed).
4.Push new fan blade on shaft.
5. Replace cardboard cover.
6. Plug in refrigerator, write nasty letter to Frigidaire.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

I removed a couple of screws from the old part, and inserted the new part. Replaced the screws and I was done. No problem. I'm an almost 60 year old woman, and fixed this myself. It was so easy.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

I popped the new one in. My cat could have done it

All I did was to take out the cracked pan and slide in the new one.Excellent service.I ordered the pan late evening one day the part arrrived not the next day but the day after.I expected that it would have taken a week or better.I recommend Part Select.com because of this.

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Followed the steps in the video on your site, really easy to do.

The most difficult part was the removal of the existing fan and shroud. There is very little room to work between the condenser and the coils where the fan is located. The old shroud had to be removed as it was not compatible with the mounting for the new fan motor and blade. Make sure to unplug the refrigerator and give the coils some time to cool down. The first step was to remove the old fan blade... it simply pulls off. Next you need to remove the two bolts holding the fan shroud to the floor of the refrigerator. Then you need to remove the old fan motor from the shroud... unplug the wire connection and remove two small bolts that hold it on. I was lucky to have a VERY small ratchet to get into these tight spaces. Now is the really hard part, removing the metal fan shroud takes a lot of twisting and turning to get it out. The coils have a little play in them, but you must be very careful of the tubing and connections. Also, the coils are very sharp. Once this is out, IF you can get it out....I had my doubts along the way, you can start to put the new parts in... beginning with the new fan shroud which fortunately is made of plastic and has some give which makes it easier to get in. Then you can mount the new motor to the shroud with the three new screws. Plug in the wire connection, add the foam tape to the shroud and mount the shroud to the floor of the frig with the original two bolts. Lastly, attach the fan blade. This replacement kit is well constructed, fits perfectly and contained all the necessary parts (fan motor with wiring connection, mounting screws, wire connection adapter, fan shroud, foam tape and fan blade), but no detailed instructions come with it. I was lucky to get the old fan shroud out without doing any damage to the surrounding parts, but this part was very difficult for a do it yourself person. I would be interested to know if a professional has some other tips for this part of the replacement process.