EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

25355333602 Kenmore Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bottom Door Bin – Part Number: 240323002
$57.15
In Stock
Bottom Door Bin
★★★★★
★★★★★
(135)
Part #240323002
The Bottom Door Bin is also commonly known as a "cantilever shelf" is a clear plastic drawer which holds items in the bottom area of your fridge's interior, on the door. This OEM part is very easy to install and will not require any tools, you will just need to snap the mounting tabs into place for removal and installation. If damaged you will notice visible damage or have problems holding items in the fridge. If damaged, it should be replaced. Check your model number and user manual to see if this is the right part for you. This is important, as many fridges use multiple door bins, many of which vary slightly. This part is sold individually.
Crisper Cover Support - Front – Part Number: 241993101
$13.12
In Stock
Crisper Cover Support - Front
★★★★★
★★★★★
(85)
Part #241993101
This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is an easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.
Crisper Support - Rear – Part Number: 241993001
$17.18
In Stock
Crisper Support - Rear
★★★★★
★★★★★
(21)
Part #241993001
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your user manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.
Refrigerator Water Inlet Valve – Part Number: 242252702
$68.15
In Stock
Refrigerator Water Inlet Valve
★★★★★
★★★★★
(124)
Part #242252702
The function of the Refrigerator Water Inlet Valve (Triple Solenoid Water-Valve, Water Valve, Water Inlet Valve, Refrigerator Water Inlet Valve Assembly) is to release water from the supply line when activated, and send it through to your water dispenser or ice maker in your refrigerator. The water inlet valve is located at the back of the refrigerator, and connects to the water supply. The valve can break from material fatigue or normal use. If your water inlet valve is malfunctioning, you could be getting a lack of water to the inside of your refrigerator. Your ice maker may not produce cubes or your water dispenser may not work. The water inlet valve must be replaced if the solenoids no longer have continuity or the valve has internal blockage. This valve measures approximately 7 inches long and 4.5 inches wide, and is constructed of plastic and metal. It comes in blue, and includes the valve and mounting bracket.
Door Bin - Clear – Part Number: 240356402
$78.05
In Stock
Door Bin - Clear
★★★★★
★★★★★
(74)
Part #240356402
This genuine refrigerator door bin is perfect for storing items on your fridge door. Made from clear plastic, it’s easy to install with no tools required—just snap it into place. Ideal for replacing cracked or stained bins, it’s sold individually.
Meat Drawer Rail - Right Side – Part Number: 240356501
$59.35
In Stock
Meat Drawer Rail - Right Side
★★★★★
★★★★★
(57)
Part #240356501
As you look into the fridge, this drawer support track is located on the right-hand side. This item is white in color and made of plastic. The drawer support track can wear out over time. The only tool required is a Phillips screwdriver. Empty out the drawer and remove it by sliding it forward. Lift out the shelf, remove the screw on the side of the shelf, remove the rail by pushing the rail forward and snapping out of place, insert new rail, and install the screw back in. Now the shelf can be put back into the refrigerator. The mounting screws are sold separately.
Hinge Bearing – Part Number: 240328201
$31.47
In Stock
Hinge Bearing
★★★★★
★★★★★
(29)
Part #240328201
Sold individually. Also known as a short door closing cam.
Door Closing Cam – Part Number: 240457701
$59.35
In Stock
Door Closing Cam
★★★★★
★★★★★
(32)
Part #240457701
Sold individually. This cam is located at the bottom of the fridge/freezer door.
Defrost Thermostat Kit – Part Number: 5303918214
$39.55
On Order
Defrost Thermostat Kit
★★★★★
★★★★★
(27)
Part #5303918214
If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with the clip, leads, and one heat shrink. To access the defrost thermostat for this repair, you will need to remove your freezer shelves, as well as the back panel of your freezer. To complete this repair, you will need a 1/4-inch nut driver, a set of wire strippers and crimpers, and a heat gun or blow dryer. Before you begin this repair, be sure to disconnect the power source from the appliance.
Refrigerator Ice Maker Assembly – Part Number: 241798231
$87.51
In Stock
Refrigerator Ice Maker Assembly
★★★★★
★★★★★
(99)
Part #241798231
This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
Crisper Glass Insert – Part Number: 240350649
$102.37
In Stock
Crisper Glass Insert
★★★★★
★★★★★
(30)
Part #240350649
Cracked crisper glass? This replacement insert is just what you need. It’s about 17.12" by 15.40" and fits right into the frame above your crisper drawers, giving you extra shelf space and keeping things neat. Made of sturdy glass and easy to install—just slide the old one out and pop the new one in. Sold individually, so make sure it matches your fridge model before ordering!
Light Bulb – Part Number: 316538904
$27.45
In Stock
Light Bulb
★★★★★
★★★★★
(13)
Part #316538904
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the internal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.

Manuals & Care Guides for 25355333602

Click to download

Common Symptoms of the 25355333602

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
water leaking out of refrigerator
608 of 723 people found this instruction helpful.
  • Jose from Alexandria, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
Was this helpful?
Thank you for voting!
Tab on bottom door bin broke off
541 of 573 people found this instruction helpful.
  • Mark from Redlands, CA
  • Really Easy
  • Less than 15 mins
Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door.
Was this helpful?
Thank you for voting!
icemaker stopped making ice
356 of 426 people found this instruction helpful.
  • David from New Bern, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if t he maker dumped the ice into the bin.
Was this helpful?
Thank you for voting!