24AF510B790 (2005-2) MTD Log Splitter - Overview

This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your...Read more owners manual to determine the exact location. While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations. Customers rate this repair as Easy.

This rubber and plastic spider bushing is a genuine OEM part for various makes of log splitters and is sold as an individual part. Measuring at approximately 2-inches by 2-inches, this bushing is attached to the motor or drive shaft and is used to support the rotating shaft and other components, all while allowing smooth rotation and prop...Read moreer alignment. The spider bushing rides between the couplings, connecting the engine and the hydraulic pump. If you notice excessive vibrations from the motor, check the drive motor shaft for a cracked bushing or couplings, since they work together and are often replaced at the same time.

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

Introducing the Adjustable Gib by MTD, a vital component for your log splitter. This 2'' long spacer is designed to be positioned between the wedge assembly and back plate of your log splitter. Its role is crucial for the seamless operation of your equipment, ensuring maximum productivity. Should your gib be worn or damaged, a replacement...Read more is readily at hand to take its place. To ensure safety during installation, it is recommended to wear work gloves. Upgrade your log splitter's performance today with our MTD Adjustable Gib.

This coupler connects the engine or motor to the hydraulic pump in your lawn equipment. It has a 0.5-inch inside diameter and is typically located near the rear coupling support bracket. If the coupler is broken, you will notice excessive play, cracks, or a loss of power transmission. Failure to replace a broken coupler can result in redu...Read moreced power, poor operation, or complete equipment failure. To remove the coupling from your machine, remove any retaining bolts, screws, or clamps securing it in place using a wrench or socket. Afterward, gently wiggle or twist the coupling to release it. This replacement part is sourced directly from its original equipment manufacturer and is sold individually.

This back plate, also known as a wedge plate, is sourced directly from the manufacturer for use in log splitters. It is a flat, metal plate found at the rear end of the machine, with a length of 8 inches and a width of 2 inches. It provides support and stability to the log splitter during use. The plate may fail due to excessive stress, p...Read morehysical damage, or corrosion. If the plate has cracks, or bends, the log splitter will become unstable and unsafe to operate. The internal components of the log splitter may also fall out of alignment and cause further damage to the equipment. Use a wrench to remove the fasteners that secure the plate to the log splitter frame. Clean the mounting area and install the new plate. Reinstall the fasteners and be careful not to overtighten them as this can damage the surface of the plate.

This genuine manufacturer-sourced component is specially made for use with MTD and Troy-Bilt log splitters. It is an identical replacement for a missing or a faulty coupling that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep ...Read morein mind this high-quality part is made of durable metal and is sold individually. Note, the other #718-04392 Coupling, . 500 is sold separately.

The Push Cap is a black plastic cap which secures to the end of a shaft to prevent injury. It can be installed with a hammer and is rated as "Easy" to install. If the part appears damaged or worn down in a way that could cause injury, it should be replaced. Refer to your make, model and diagrams to check if this is the right part for you.

This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers. This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will b...Read moree out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.

This special jam nut is sourced directly from the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications depending on your tool, please refer to appropriate diagrams for correct location and use of this part. It is made of high-quality metal and it is sold individually.

This OEM replacement washer is often used on several different types of lawn and garden equipment, but can also be used on compatible home trimmers. It is made of metal, meaning it is vulnerable to corrosion and will produce more noise from your lawn equipment or trimmer if it has broken. Its main purpose is to reduce rattling and noise, ...Read moreor to better secure and evenly distribute pressure between two different parts. This washer has a .38-inch inner diameter, .87-inch outer diameter, and .09-inch thickness and is sold individually.

This grease seal, also known as an oil seal or a shaft seal, in your log splitter or chipper shredder serves as a protective barrier. It keeps lubrication inside the bearings and stops dirt from entering them. It is commonly located in the wheel hubs or axle assemblies of your machine. A broken grease seal leads to contaminated bearings. ...Read moreYour machine will then undertake more friction and can overheat, reducing its performance. You will need a seal puller or a flathead screwdriver to pry a grease seal out of your machine. When installing the new grease seal, apply a thin layer of lubricant to its inner surface before pressing it into its housing. Please be informed that this OEM-certified component is sold individually.