246435-0112-B1 Briggs and Stratton Engine - Overview

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This is a genuine replacement pre-cleaner filter used with Briggs and Stratton engines. It is supplied directly from original equipment manufacturer. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper and metal. This item is sold individually. Replacing this filter is a simple that that would only require a wrench.

It is a genuine item that is supplied by the original equipment manufacturer for Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is a special component that provides a tight seal for the PTO side of the crankcase. Over time it may wear out and begin to crack eventually requiring a replacement...Read more. Check the appropriate diagrams for your specific model to ensure the correct installation of the new seal-oil. To perform this repair you will need a variety of tools such as a screwdriver, a wrench set, pliers and a tool to pick out the old seal. Make sure to drain the oil before starting this repair. Keep in mind, one durable rubber part is included.

This is a genuine replacement part manufactured for use with small engines. The spark plug is used to fire the air-fuel mixture inside the cylinder. This spark plug is available as an individual replacement part, please see model diagram for associative parts.

This replacement screw is a genuine hardware that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part is made of high-quality metal and it is sold individually, you will need either a wrench or a flat-head screwdriver to install or remove it.

This is an authentic Briggs & Stratton replacement part, sourced from the original manufacturer for use with small engines. The special air cleaner cover is commonly used to secure the air filter to the air cleaner base. This air cleaner cover is available as an individual replacement part, please see model diagram for associative parts.

This is available individually and is made of metal. The valve spring is part of the cylinder head. During the installation process, a set of pliers might be needed to replace this part. It will require replacing if it becomes broken. This is a genuine item that is supplied by the original equipment manufacturer for use with lawn tractors made by Briggs & Stratton, Toro, and Lawn Boy.

It is an authentic OEM sourced part which is specially made for use with Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is an identical replacement for a faulty or a missing spark plug wrench that was included with a new unit. The wrench allows a user to secure or remove a spark plug. Refer ...Read moreto the appropriate diagrams for your model to ensure the exact location and the correct application of this component. A screwdriver will be needed to secure or remove this part. This high-quality part is made of durable metal and is sold as an individual item. Note. This spark plug wrench fits 5/8" and 13/16" spark plugs.

The control knob is part of the speed control panel. This item is made of plastic and is sold individually. It is an authentic OEM sourced item which is specifically produced for use with blowers, engines, generators, and vacuums made by Briggs & Stratton and Toro. It may require a set of pliers during installation. This part may become broken and will need to be replaced.

This is a genuine Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with small engines. The starter rope coils around the starter pulley and is used to rotate the pulley when starting the engine. This item is sold as an individual replacement part.

This is an OEM part sourced directly from the manufacturer. The rewind spring is designed for use in engines from Briggs & Stratton. This part is made of metal, and is used in the starter assembly to coil the rope back onto the reel. You may require a wrench and screwdriver when replacing this part. This item is sold individually.

This is an authentic replacement part manufactured for use with Briggs & Stratton small engines. The rewind starter is used to engage the flywheel when starting the engine. This starter is a complete part assembly that includes the housing, rope and handle, spring, pulley, pawls, and pawl friction plate. The recoil starter assembly is sold as an individual replacement part.