245RXEPA (20023100001-Current) Husqvarna Brush Cutter - Overview

This manufacturer-grade bevel gear grease is used to grease transmissions, bevel gears and other gear case assemblies.

This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This screw is an authentic high-quality item that is specially produced for Husqvarna and Poulan handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to appropriate diagrams for the correct location and use of this screw. Please note this high-quali...Read morety hardware is sold individually, keep in mind you will need an Allen wrench also known as a hex key to secure or remove it.

Primarily used in chainsaws, this Starter Rope is an exact replacement part for hundreds of models. It is white and sold individually, not as part of a kit or assembly. The Starter Rope will need to be replaced once you notice signs of it fraying, wearing, or it breaks off. Customers rate this repair as Easy.

It is a genuine manufacturer-sourced component which is specially produced for use with Husqvarna and Poulan lawn and garden equipment. This replacement gasket is used to provide an air-tight seal for the fuel cap to prevent any leaks. Over time the material may begin to deteriorate and crack eventually requiring replacement. It is a high...Read more-quality component which is made of durable rubber material and it is sold individually.

This metering diaphragm is an original part for use in edgers, blowers, trimmers, and chainsaws made by Poulan, Paramount, Weed Eater, Husqvarna, and Jonsered. It fits between the metering diaphragm gasket and the metering diaphragm cover. It is made of a thin material and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part and keep in mind that it is sold individually.

This item has been sourced from the original manufacturer to be used with chainsaws and brushcutters from Husqvarna and Jonsered. The metal recoil spring is part of the starter assembly and is used to pull the starter rope back after it is pulled to start the motor. This spring is priced as a single item.

This screw is an authentic OEM part which made for Husqvarna chainsaws. It is designed for multiple uses based on your tool. Please refer to diagrams for correct location and applied use of this screw. It includes one (1) metal screw per order. This is a hex head item so you would need a hex key/allen wrench to install or remove it.

This fuel pump diaphragm, also called a membrane or a gasket, is what helps pump fuel from the tank to the engine of your gas-powered lawn equipment. It is normally found attached to the carburetor assembly itself. You can tell that the diaphragm is broken when your engine is not starting properly, lacks power, or frequently stalls. You m...Read moreay also notice that your machine is leaking fuel or smells strongly of gasoline. A broken diaphragm could lead to engine performance problems, and it may eventually stop working altogether. When replacing your old diaphragm, you will need a wrench to disconnect it from the fuel pump housing. Kindly note that this OEM-sourced component is sold individually.

This part is an OEM sourced directly from the manufacturer. It is intended to be used in chainsaws and brushcutters made by Husqvarna and Jonsered. The impulse pipe attaches to the bulkhead assembly next to the intake sleeve. This is a small rubber part and will need to be replaced if it becomes lost. The pipe is available as an individual replacement.

This is a genuine Poulan, Husqvarna and Jonsered part for use with Chainsaws.The Recoil starter pulley spins the flywheel to start the engine. This part is sold individually. The most common reason for replacing the starter pulley is when it is broken or stuck, causing the rope to not rewind and the engine to not start. The tools that you...Read more will need to replace the starter pulley are a Torx head screwdriver and needle-nose pliers.

This OEM locking pin is found in your handheld lawn equipment to hold a part, such as a cutting head, spool, or guard, in place and keep it from coming in loose while you are using your machine. If the pin is broken, the component it is supposed to be securing will become wobbly and loose, which can cause your machine to malfunction. To r...Read moreemove a broken locking pin, you can use pliers or a small screwdriver to pull it straight out of the hole. If the pin is stuck, you may need to wiggle it back and forth gently while pulling on it. Take into consideration that this part is sold individually, so refer to your instruction manual to confirm how many of these pins your machine will need.