245437 (0284-B2) Briggs and Stratton Engine - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This is a genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. The needle valve opens and closes to control the flow of fuel into the carburetor. It is made out of metal and it is sold individually. You would need a screwdriver and pliers to complete this repair.

It is a genuine item that is supplied by the original equipment manufacturer for Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is a special component that provides a tight seal for the PTO side of the crankcase. Over time it may wear out and begin to crack eventually requiring a replacement...Read more. Check the appropriate diagrams for your specific model to ensure the correct installation of the new seal-oil. To perform this repair you will need a variety of tools such as a screwdriver, a wrench set, pliers and a tool to pick out the old seal. Make sure to drain the oil before starting this repair. Keep in mind, one durable rubber part is included.

This authentic part has been sourced from the original manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. It provides a high-quality rep...Read morelacement for a damaged or a missing component that was installed on a new unit. Keep in mind this high-quality item includes one durable metal bowl-float, the screw, the washer, and the o-ring. Refer to the diagrams of your model for the correct installation.

This item is an OEM sourced replacement part that is intended to be used with small engines for snowthrowers and riding lawnmowers. The seal is used as a replacement of an original part from Briggs & Stratton or Toro machines. This item is used to prevent oil or fuel leaks between two different part assemblies. The item can have different...Read more applications depending on the model of the engine or machine. This seal is sold individually.

This is a genuine OEM supplied replacement carburetor float designed for lawn and garden equipment engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin used to secure the float. To complete this repair you would need a wrench and pliers. • Make sure to ...Read moreremove the spark plug • Remove carburetor bowl • Remove old float and secure the new one in place • Re-assemble and test the unit

This fuel filter bowl is an OEM direct from Briggs & Stratton. Compatible with many small engines, this plastic item is fitted with the fuel shut-off valve. No tools should be required for the replacement. The fuel filter bowl helps to separate water from the fuel, and is sold individually. The fuel filter bowl is sold individually.

This is an authentic Briggs and Stratton replacement part manufactured for use with small engines. This pleated paper filter comes in the rubber frame, and is used to clean the air entering the carburetor. This air cleaner filter cartridge is sold individually, and many require a foam pre-filter which is sold separately.

This authentic manufacturer-sourced component is specially made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or a faulty pre-cleaner filter that was installed on a new unit. The part provides an identical layer of filtration, unfortunately, over time...Read more it will wear out and get clogged eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality filter is made of durable material and is sold individually.

This part is an OEM from Briggs & Stratton. The switch and key is compatible with many small engines. This ignition component is sold individually, and includes a washer, nut, decal and key set. Please refer to specific manual and diagrams for making the repair. A screwdriver, pair of pliers and a wrench set are often necessary for the installation.