245437 (0006-H1) Briggs and Stratton Engine - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.

This is a genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. The needle valve opens and closes to control the flow of fuel into the carburetor. It is made out of metal and it is sold individually. You would need a screwdriver and pliers to complete this repair.

It is a genuine item that is supplied by the original equipment manufacturer for Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is a special component that provides a tight seal for the PTO side of the crankcase. Over time it may wear out and begin to crack eventually requiring a replacement...Read more. Check the appropriate diagrams for your specific model to ensure the correct installation of the new seal-oil. To perform this repair you will need a variety of tools such as a screwdriver, a wrench set, pliers and a tool to pick out the old seal. Make sure to drain the oil before starting this repair. Keep in mind, one durable rubber part is included.

This item is an OEM sourced replacement part that is intended to be used with small engines for snowthrowers and riding lawnmowers. The seal is used as a replacement of an original part from Briggs & Stratton or Toro machines. This item is used to prevent oil or fuel leaks between two different part assemblies. The item can have different...Read more applications depending on the model of the engine or machine. This seal is sold individually.

This replacement screw is a genuine hardware that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part is made of high-quality metal and it is sold individually, you will need either a wrench or a flat-head screwdriver to install or remove it.

This fuel filter bowl is an OEM direct from Briggs & Stratton. Compatible with many small engines, this plastic item is fitted with the fuel shut-off valve. No tools should be required for the replacement. The fuel filter bowl helps to separate water from the fuel, and is sold individually. The fuel filter bowl is sold individually.

This is an authentic Briggs and Stratton replacement part manufactured for use with small engines. This pleated paper filter comes in the rubber frame, and is used to clean the air entering the carburetor. This air cleaner filter cartridge is sold individually, and many require a foam pre-filter which is sold separately.

This authentic manufacturer-sourced component is specially made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or a faulty pre-cleaner filter that was installed on a new unit. The part provides an identical layer of filtration, unfortunately, over time...Read more it will wear out and get clogged eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality filter is made of durable material and is sold individually.

This part is an OEM from Briggs & Stratton. The switch and key is compatible with many small engines. This ignition component is sold individually, and includes a washer, nut, decal and key set. Please refer to specific manual and diagrams for making the repair. A screwdriver, pair of pliers and a wrench set are often necessary for the installation.

This is an OEM replacement part for Briggs and Stratton, Murray, Snapper, and Simplicity engines. When engaged the ignition key starts the lawn tractor. This part is made of metal and is sold in a set of two. There are no tools needs to use this part, as it comes pre-assembled and really to use.

It is an authentic OEM sourced part which is specially made for use with Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is an identical replacement for a faulty or a missing spark plug wrench that was included with a new unit. The wrench allows a user to secure or remove a spark plug. Refer ...Read moreto the appropriate diagrams for your model to ensure the exact location and the correct application of this component. A screwdriver will be needed to secure or remove this part. This high-quality part is made of durable metal and is sold as an individual item. Note. This spark plug wrench fits 5/8" and 13/16" spark plugs.