245436 (0008-H1) Briggs and Stratton Engine - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This is a genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. The needle valve opens and closes to control the flow of fuel into the carburetor. It is made out of metal and it is sold individually. You would need a screwdriver and pliers to complete this repair.

This item is an OEM sourced replacement part that is intended to be used with small engines for snowthrowers and riding lawnmowers. The seal is used as a replacement of an original part from Briggs & Stratton or Toro machines. This item is used to prevent oil or fuel leaks between two different part assemblies. The item can have different...Read more applications depending on the model of the engine or machine. This seal is sold individually.

This replacement screw is a genuine hardware that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part is made of high-quality metal and it is sold individually, you will need either a wrench or a flat-head screwdriver to install or remove it.

This is a geniune OEM part. The Briggs & Stratton, 10-16 amp voltage regulator is composed of metal, wiring and plastic parts. The regulator is compatible with many lawn and garden machines. This part is connected to the engine's terminals, and has been designed to manage the voltage in the device's electrical system. A screwdriver and a ...Read moresocket set are needed in making the removal and repair. It is recommended to refer to the manual and diagrams for repair instructions. This item is sold individually.

This fuel filter bowl is an OEM direct from Briggs & Stratton. Compatible with many small engines, this plastic item is fitted with the fuel shut-off valve. No tools should be required for the replacement. The fuel filter bowl helps to separate water from the fuel, and is sold individually. The fuel filter bowl is sold individually.

This part is an OEM from Briggs & Stratton. The switch and key is compatible with many small engines. This ignition component is sold individually, and includes a washer, nut, decal and key set. Please refer to specific manual and diagrams for making the repair. A screwdriver, pair of pliers and a wrench set are often necessary for the installation.

This is an OEM replacement part for Briggs and Stratton, Murray, Snapper, and Simplicity engines. When engaged the ignition key starts the lawn tractor. This part is made of metal and is sold in a set of two. There are no tools needs to use this part, as it comes pre-assembled and really to use.

It is an authentic OEM sourced part which is specially made for use with Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is an identical replacement for a faulty or a missing spark plug wrench that was included with a new unit. The wrench allows a user to secure or remove a spark plug. Refer ...Read moreto the appropriate diagrams for your model to ensure the exact location and the correct application of this component. A screwdriver will be needed to secure or remove this part. This high-quality part is made of durable metal and is sold as an individual item. Note. This spark plug wrench fits 5/8" and 13/16" spark plugs.

The metal screw attaches to the muff guard bracket. It is a genuine replacement part sourced from the original manufacturer for use with blowers, engines, generators, pressure washers, snowblowers, and vacuums made by Briggs & Stratton, Toro, and Lawn Boy. This item is available as an individual replacement part. When replacing this screw a wrench will be needed. It will need to be replaced if it strips or breaks.

This authentic item is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or a faulty screw that helps to adjust the choke. Make sure to refer to the owners manual and the appropriate diagram of your model fo...Read morer the exact location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.