245430 Briggs and Stratton Engine - Overview

This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation, steady power output, and easier starting. Ideal for routine maintenance or replacement, it supports dependable engine performance in lawn and garden equipment, generators, and similar outdoor power machines.

This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This is a genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. The needle valve opens and closes to control the flow of fuel into the carburetor. It is made out of metal and it is sold individually. You would need a screwdriver and pliers to complete this repair.

It is a genuine item that is supplied by the original equipment manufacturer for Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is a special component that provides a tight seal for the PTO side of the crankcase. Over time it may wear out and begin to crack eventually requiring a replacement...Read more. Check the appropriate diagrams for your specific model to ensure the correct installation of the new seal-oil. To perform this repair you will need a variety of tools such as a screwdriver, a wrench set, pliers and a tool to pick out the old seal. Make sure to drain the oil before starting this repair. Keep in mind, one durable rubber part is included.

This authentic part has been sourced from the original manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. It provides a high-quality rep...Read morelacement for a damaged or a missing component that was installed on a new unit. Keep in mind this high-quality item includes one durable metal bowl-float, the screw, the washer, and the o-ring. Refer to the diagrams of your model for the correct installation.

This item is an OEM sourced replacement part that is intended to be used with small engines for snowthrowers and riding lawnmowers. The seal is used as a replacement of an original part from Briggs & Stratton or Toro machines. This item is used to prevent oil or fuel leaks between two different part assemblies. The item can have different...Read more applications depending on the model of the engine or machine. This seal is sold individually.

This is a genuine OEM supplied replacement carburetor float designed for lawn and garden equipment engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin used to secure the float. To complete this repair you would need a wrench and pliers. • Make sure to ...Read moreremove the spark plug • Remove carburetor bowl • Remove old float and secure the new one in place • Re-assemble and test the unit

This replacement screw is a genuine hardware that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part is made of high-quality metal and it is sold individually, you will need either a wrench or a flat-head screwdriver to install or remove it.

This is a geniune OEM part. The Briggs & Stratton, 10-16 amp voltage regulator is composed of metal, wiring and plastic parts. The regulator is compatible with many lawn and garden machines. This part is connected to the engine's terminals, and has been designed to manage the voltage in the device's electrical system. A screwdriver and a ...Read moresocket set are needed in making the removal and repair. It is recommended to refer to the manual and diagrams for repair instructions. This item is sold individually.

This fuel filter bowl is an OEM direct from Briggs & Stratton. Compatible with many small engines, this plastic item is fitted with the fuel shut-off valve. No tools should be required for the replacement. The fuel filter bowl helps to separate water from the fuel, and is sold individually. The fuel filter bowl is sold individually.