243432-0733-99 Briggs and Stratton Engine - Overview

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually. Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy. Locate and replace the start spring inside the starter housing; no special tools are required for this job.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.

This is a genuine OEM sourced replacement air cleaner cartridge commonly utilized on Briggs and Stratton engines. It installed to filter our dust and other contaminants from entering carburetor and the engine. Please note, this pleated paper filter is sold individually. Keep in mind that the foam pre-cleaner is sold separately. Replacing...Read more this air cleaner cartridge is a simple task that should only require a wrench. • Remove the cover • Remove the old cartridge • Secure the new one in place • Secure the cover

This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.

This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.