243-645-100 (1983) Cub Cadet Log Splitter - Overview

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers. This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will b...Read moree out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.

This grease seal, also known as an oil seal or a shaft seal, in your log splitter or chipper shredder serves as a protective barrier. It keeps lubrication inside the bearings and stops dirt from entering them. It is commonly located in the wheel hubs or axle assemblies of your machine. A broken grease seal leads to contaminated bearings. ...Read moreYour machine will then undertake more friction and can overheat, reducing its performance. You will need a seal puller or a flathead screwdriver to pry a grease seal out of your machine. When installing the new grease seal, apply a thin layer of lubricant to its inner surface before pressing it into its housing. Please be informed that this OEM-certified component is sold individually.

This Bell-Wash Flat Washer is an OEM part that measures .40 inches I.D. x 88 inches O.D. This washer is a silver, metal, washer sold individually. This part is rated as Easy to install by customers. If missing or damaged (likely due to fatigue) it should be replaced. Refer to your owners manual to ensure this is the correct part for you.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers and lawnmowers from Ryobi and MTD. The metal nut is used with different types of machines and the application of the nut can vary based on the model of the equipment. It is recommended to verify the part\\\'s compatibility a...Read morend usage by reviewing your model\\\'s diagram. This nut is available as an individual replacement part. A hex socket wrench and a driver are needed when installing this part.

This is an original replacement part sourced directly from the manufacturer. The shoulder screw is commonly found in MTD yard equipment such as chippers, log splitters, and lawn tractors. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The shoulder screw is sold as an individual replacement part.

This is an original MTD replacement part. The screw is commonly found in tillers, lawn mowers, and snowblowers. This part is made of metal, and is generally used to secure components in the machine. It may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the mach...Read moreine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

This OEM Hex Nut 5/16-24 is a silver, metal nut. This certified part is sold individually. It can be applied with a Wrench or Socket and Torque Wrench to the bracket on the rear of the auger house to secure a bracket to the back of the auger housing. Simply torque to the manufacturer specifications. Refer to your owners manual to find o...Read moreut if this is the part you need. Over time the part may be damaged by fatigue and will come loose due to damaged threads, at which time it should be replaced.