242-610-929 (1992) MTD Log Splitter - Overview

This genuine drive belt is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman lawn mowers and edgers. Made from flexible rubber, it transfers power from the engine to the pulley that drives the cutting blades. Over time, the belt may become brittle or cracked due to wear and exposure, req...Read moreuiring replacement to maintain optimal performance. Measuring 3L x 35.80 inches, this belt is sold individually. A wrench may be needed for installation, depending on your equipment model.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers. This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will b...Read moree out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.

This grease seal, also known as an oil seal or a shaft seal, in your log splitter or chipper shredder serves as a protective barrier. It keeps lubrication inside the bearings and stops dirt from entering them. It is commonly located in the wheel hubs or axle assemblies of your machine. A broken grease seal leads to contaminated bearings. ...Read moreYour machine will then undertake more friction and can overheat, reducing its performance. You will need a seal puller or a flathead screwdriver to pry a grease seal out of your machine. When installing the new grease seal, apply a thin layer of lubricant to its inner surface before pressing it into its housing. Please be informed that this OEM-certified component is sold individually.

This genuine flat washer distributes fastener pressure across the mounting surface and may also serve as a spacer in compatible outdoor power equipment assemblies. It measures 0.385 of an inch across the inner opening,0.870 of an inch across the outer edge, and 0.090 of an inch thick. This washer is sold individually, and you should confirm the equipment you are repairing matches with this washer before ordering.

This is a genuine item that is supplied by the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications, please make sure to refer to the diagrams of your model for the correct location and application of this item. Keep in mind it is made of durable metal and is sold individually.

This Cotter Pin is a silver 5/32x1-1/4 metal part, sold individually and certified by the original equipment manufacturer. It connects to the axel shaft after the wheel and washer have been installed but before the hub cap. It is used to prevent the wheel from falling off, and if it breaks (due to fatigue) the wheel will fall off. Check...Read more your model number for the correct size of replacement cotter pin to know you are ordering the correct model. This is a one-time use product, which should be replaced during any other repair in which it is disturbed or dislodged.

This is an authentic replacement part, sourced from the original manufacturer for use with hydraulic log splitters. The metal nipple pipe is commonly used to link the hydraulic cylinder and the control valve. This nipple pipe is available as an individual replacement part, please see model diagram for associative parts.

This OEM Cone Bearing, also known as a Tapered Bearing, is a silver, .75 I.D., metal part. Sold individually, it attaches inside the wheel hub, and customers have rated the installation as Medium Difficulty. It is recommended to pack the bearing before installation. This part reduces friction on a moving part, inside of a stationary par...Read moret. When it breaks, you will hear a grinding, growling or squealing sound. It must be replaced when worn or damaged (such as if there are scores on the rollers or on the mandrel).

This is a genuine Troy-Bilt replacement part sourced directly from the manufacturer. The cup bearing is commonly found in Troy-Bilt tillers. This part is made of metal, and is used with the cone bearing to join the drive shaft with the transmission housing. You may require pliers when replacing this part. It is advisable when removing ...Read moremultiple parts to keep careful track of their order so they can be reassembled correctly. This item is sold individually.