2414NB Makita Chop Saw - Overview

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This flange 90 is an OEM direct from Makita. The metal part is designed for use with many saw models. This component assists with securing the blade, and is sold individually. For the repair, a wrench set and a Phillips head screwdriver is often necessary.

This is an authentic Makita replacement part that has been sourced from the original manufacturer and is intended to be used with chop saws and cut-off saws. The vice nut fits into the screw guide and is used to fasten the vice screw. This item is available as an individual replacement part.

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

This switch activator button is a genuine Makita replacement part, It is sold individually. It has to be pressed to activate the power switch. This is a very common replacement part. It is advised to order one or two extra to keep on hand. This Makita switch button is compatible with the tools listed below, and it is not guaranteed to fit any other power tool models.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

It is a genuine manufacturer-sourced replacement part, it is specially designed for use with Makita chop saws. This special flat head screw is used to secure the safety guide. It is a high-quality component which is made of durable metal and it is sold individually. You will need a Phillips head screwdriver to install or remove this hardware.

This is a genuine manufacturer-sourced replacement bolt which is specially designed for use with Makita saws. It is a standard hardware which has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams of your unit for the correct location and use of this item. This high-quality hex socket head bolt is made of durable metal and it is sold individually.

It is a high quality OEM sourced replacement ring that is specially designed for use with Makita chop saws. Two of these rings are secured on both sides of the inner flange that helps to secure the saw blade. Please note one durable metal ring is included per order.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Makita power tools. It is an identical replacement for a missing or damaged rubber pin that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicat...Read moreion of this hardware. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

This is an authentic part from Makita for use in chop saws and cut-off saws. The screw guide attaches to the base and is made of metal. When replacing this item a wrench set might be required during the installation process. It will require replacing if it becomes broken. This part is available as an individual replacement.

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fi...Read morex an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.