This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.
An engine that surges, stalls, or will not stay running can have dirt or worn seals inside its float carburetor. This rebuild kit contains gaskets and small service pieces for restoring the carburetor rather than replacing the complete unit. Inspect the fuel supply and ignition system first, then confirm the engine identification and carb...Read moreuretor design. Work only on a cool engine in a ventilated area. Drain all fuel, disconnect the spark plug wire, and keep sparks and cigarettes away. Photograph the linkages, clean passages without enlarging them, install each gasket in the correct order, and check carefully for leaks before starting the engine.
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.
It is a genuine item that is supplied by the original equipment manufacturer for Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is a special component that provides a tight seal for the PTO side of the crankcase. Over time it may wear out and begin to crack eventually requiring a replacement...Read more. Check the appropriate diagrams for your specific model to ensure the correct installation of the new seal-oil. To perform this repair you will need a variety of tools such as a screwdriver, a wrench set, pliers and a tool to pick out the old seal. Make sure to drain the oil before starting this repair. Keep in mind, one durable rubber part is included.
This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.
This OEM engine screw is a genuine Briggs & Stratton replacement fastener designed for secure, vibration-resistant attachment of engine components in small gasoline engines and outdoor power equipment. Manufactured to exact factory specifications, it provides proper thread engagement and clamping force to help prevent loosening, reduce vi...Read morebration, and maintain long-term engine reliability under operating stress. Built with durable, corrosion-resistant materials for extended service life, it is an ideal replacement when original screws are missing, stripped, or worn, helping ensure safe assembly, consistent performance, and proper engine operation.
This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy-duty steel and engineered to apply even pulling force, it makes accessing the magneto, crankshaft key, or ignition system straightforward d...Read moreuring repairs or overhauls. Built to OEM specifications for durability and precise fit, it’s a reliable tool for maintaining lawn mowers, generators, and pressure washers with compatible engines.
The float valve is used to allow fuel into the float chamber when the chamber has been drained and to stop fuel from entering the chamber when it is full. It provides an identical replacement for a missing or a faulty component that was installed on a new unit. This authentic part is supplied by the original equipment manufacturer for use...Read more with Kawasaki engines commonly installed on lawn and garden equipment. Please make sure to refer to the appropriate diagrams of your model to ensure the correct repair procedure. Keep in mind this high-quality valve-fuel inlet is sold as an individual item.
This manufacturer approved replacement part is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is utilized to keep the oil in the tank. Please note this durable plastic oil fill cap is sold individually.
This is a genuine replacement part that is OEM sourced to be used with small engines from Briggs & Stratton and Toro. The metal screw is used to fasten the diaphragm cover to the body of the carburetor. A screwdriver is needed to install the screw and this item is sold as an individual replacement part.
This high speed valve is an OEM part from Briggs & Stratton. Made for use with many small engines, the metal needle valve is fitted in the nozzle of the carburetor assembly. The high speed valve dispenses the proper amount of fuel to the engine. This item is sold individually, a wrench, screwdriver and a hex key are often required for the installation.