Models
>
22314
22314 ((1988)) Kenmore Range - Overview
Sections of the 22314
[Viewing 1 of 1]
Exact Part matches for your search term
[Viewing 1 of 1]
Hex nut, 5-pack
This part number matches the current model number 22314
PartSelect #: PS12399279
Manufacturer #: 22314
No Longer Available
Keep searches simple, eg. "belt" or "pump".
Cartridge 4 Spades - Stainless Steel
PartSelect #: PS8769936
Manufacturer #: JEA7000ADSA
This part has an end plug in.
$312.10
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Stove Cartridge Assembly
PartSelect #: PS9491819
Manufacturer #: JEA7000ADBA
This stove cartridge assembly, also known as a cooktop module, is a manufacturer-approved replacement part for your stove. It is black in color and comes complete with burner elements. Make sure to sh...
$309.66
In Stock
Surface Burner Switch - 240V
PartSelect #: PS12347301
Manufacturer #: W11120791
This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which i...
$90.92
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Black Radiant Element Cartridge
PartSelect #: PS9491822
Manufacturer #: JEA8120ADBA
Ultra Quick-Start radiant element with glass-ceramic surface for all Designer Line Jenn-Air cooktops. End plug-in cartridge.
$629.82
In Stock
One Piece Electric Cartridge Cover
PartSelect #: PS2104802
Manufacturer #: A341
*** May not be exactly as shown.
No Longer Available
Radiant Smoothtop Cartridge Assembly
PartSelect #: PS8768540
Manufacturer #: A122BA
Designer Line.
$496.53
In Stock
Non-Stick Griddle for Electric Elements
PartSelect #: PS2103957
Manufacturer #: A302
Griddle for Jenn-Air Designer Line cooktops. Fits over electric grill elements to provide a quality, non-stick surface for pancakes, eggs, bacon and sausages. Heats food evenly, with holes for drainin...
No Longer Available
Infinite Switch Knob
PartSelect #: PS11757573
Manufacturer #: WPY703899
This infinite switch knob is an inch and a half in diameter. It is made of plastic and has an orange indicator line as well as orange lettering denoting the 'off' position. There is also white numberi...
$26.31
In Stock
Rock Plate
PartSelect #: PS2088651
Manufacturer #: 74011338
This part is used as a support for the grill element. Sold individually.
No Longer Available
Glass Grease Collecting Jar
PartSelect #: PS11757591
Manufacturer #: WPY707869
This jar is a little over five inches long. It is made of glass and is used for collecting the grease drippings of gas ranges.
$45.50
In Stock
Questions And Answers for 22314
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 22314
[Viewing 3 of 3]Element will not heat
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner had one temperature--hot, regardless of setting
1. Killed power and removed the regulator's knob, noted the position of the old control.
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold.
3. Unscrewed the two screws holding the old control switch in ... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at.
4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch).
5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally.
6. Slide the housing back over the two screws and tightened, replace vent.
7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).
Read less
Parts Used:
-
James H from Oxford, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
105 of 119 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced grill with cooking elements
Bought a new house last fall. Jenn-Air range had two element cooktop with two element grill. Oven went out and while service man was here, I asked him to check on the price of another two heater element panel to replace the grill. He subsequently called to say the part I wanted was not available. I immediately got on the internet and
... Read more
did a search. Found it "ships same day" for what I thought was a very reasonable price at PartSelect. Unplugged the grill and plugged in the cooking plate. We now have four usable "burners" instead of two. Thanks PartSelect!
Read less
Parts Used:
-
Lee from Crystal Beach, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
63 of 80 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element was cracked
-
Gordon from Olympia, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
30 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!