The function of the grease filter is to trap grease into the filter from the exhaust air. The grease filter is intended to be used with certain downdraft cooktops and ranges. This grease filter is roughly fourteen inches long and almost twelve inches wide, and chrome in color. Removing your old grease filter and replacing it with a new on...Read moree is an easy job, users say it took them less than fifteen minutes to install. We recommend that when removing your current grease filter, you use work gloves to protect your hands and clean the entire area thoroughly before installing the new filter.
The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to repl...Read moreace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.
This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which in turn controls this switch. Made for various ranges, wall ovens and cooktops, this is a genuine OEM part that comes by itself, without any ...Read morehardware like screws or nuts. This burner switch is an electrical component that you also handle directly, so it can become faulty leading to problems like your stovetop not heating enough, overheating or staying at a fixed heat. This burner switch is a vital component for your stovetop and if it presents any of those issues, it needs to be replaced immediately. A screwdriver, set of pliers and wiring diagram will be needed for the replacement and installation process, and you will need to remove your appliance from the wall outlet first. Remove the knobs from the control panel and then gain access to the underneath portion of it with your screwdriver and disconnect the switch. Remove the wires from the burner switch with a set of pliers and disconnect the securing screws holding the switch in place. Now, you can install the new switch and reassemble the panel, being mindful of wiring each connector to the appropriate wire.
This down-draft fan switch kit comes with the switch itself and two metallic push nuts. At 125 volts,this switch will allow for 6 amps, and at 250 volts, this switch will allow for 250 volts. This switch runs at 1/4 horsepower.
This surface burner control knob allows you to adjust the heat level of your cooktop burner, from low simmer settings to high heat for cooking. It provides a secure connection to the control shaft, making it easy to select and control the desired temperature. If the original knob is cracked, worn, loose, or missing, replacing it can help ...Read morerestore proper burner control and make the appliance easier and safer to operate. Installation is simple and typically requires no tools.
This grill element is a high-performance heating component designed to deliver consistent, radiant heat for grilling functions in compatible electric ranges, ovens, and cooktops. Operating at 240 volts with a five-pronged connection, it ensures thorough and even cooking by regulating heat across the grilling surface. Constructed to meet O...Read moreEM standards, this genuine replacement part is compatible with models from Whirlpool, Jenn-Air, Kenmore, Maytag, Amana, KitchenAid, Magic Chef, and others. Common symptoms of failure include uneven heating, lack of heat during grilling or baking, or a visibly damaged element. Installation involves disconnecting power, accessing the grill cavity, and securely connecting the new element.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replaced filter
486 of 513 peoplefound this instruction helpful.
ELOISE from MILFORD, OH
Really Easy
Less than 15 mins
pulled old one out , cleaned the area & replaced with the new one.
Was this helpful?
Thank you for voting!
Old grease filter that I actually did not know I had to change
451 of 540 peoplefound this instruction helpful.
deborah from fort pierce, FL
Really Easy
Less than 15 mins
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this helpful?
Thank you for voting!
Burner had one temperature--hot, regardless of setting
110 of 131 peoplefound this instruction helpful.
James H from Oxford, NY
Really Easy
Less than 15 mins
Pliers, Screw drivers
1. Killed power and removed the regulator's knob, noted the position of the old control. 2. Took off the cover for the center vent and loosened the two screw holding the housing in place--the screws didn't have to come out completely as it is a U-shaped friction hold. 3. Unscrewed the two screws holding the old control switch in
... Read more place--lifted the housing enough to get at the old switch and carefully pulled it loose--it was a front burner so the control switch was about as far back as it could be but still wasn't that hard to get at. 4. Turned the new switch to orient the wire connectors, then, using a needle-nose pliers, removed each friction connector, one at a time, and fitted them on the new switch (note: one of the wires fitted best if it went under as opposed to around the base of the new switch). 5. Replaced the control back through the housing and screwed it in place, making sure the orientation of the control matched the way it looked originally. 6. Slide the housing back over the two screws and tightened, replace vent. 7. Replaced the knob and turned on the power.
(The above took me about twice as long to write as it did to make the repair and I write professionally but am not a professional electrician.)
Also, I bought a second control switch because, given the age of the unit, I'm sure another one will go. The second one will assure that it won't happen :-).