223-8520-00 (1985) MTD Lawn Tractor - Overview

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near the transmission or the wheels of your machine. If you notice that the machine takes longer to stop or that there is a loud scraping or grindi...Read moreng noise when you push down on the brake, your brake puck may have worn out. If it is not replaced, you risk losing braking power, which leads to equipment damage or accidents. Before any repairs, make sure that your machine is turned off and that the spark plug is disconnected. To dissemble the brake assembly and access the brake puck, use pliers or a wrench to remove any bolts or clips holding it in place. With a screwdriver, pry the brake puck out of your machine. Since this genuine OEM part is sold individually, determine the number of pucks your machine needs by consulting your user manual.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This authentic OEM hi-pro key, also called a woodruff key or key stock, is a metal component found in your lawn equipment that connects rotating parts. It is 3/16 inch wide and 5/8 inch long. It fits into a specially-shaped slot on a shaft and prevents the parts from moving or slipping out of position while your machine is running. To fin...Read mored and replace a hi-pro key on your machine, check your user guide for instructions. When removing the hi-pro key, insert a flathead screwdriver or needle-nose pliers into its groove and pry it out of its slot. Please bear in mind that this hi-pro key is sold individually.

This Flat Washer is made of durable gold-colored metal and is an authentic OEM part. It is used to spread the load under a bolt or nut and is sold individually. This part will need to be replaced if you notice any signs of cupping, corrosion, or other damage. Customers rate this repair as Easy.

It is a genuine item that is supplied by the original manufacturer for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. It is a standard hardware which may have multiple applications. This part provides an identical replacement for a damaged or a m...Read moreissing hardware that was installed on a new unit. Check the diagrams for your specific model for the exact location and the correct application of this flat washer. Note, it is made of durable metal and is sold individually.

This item is an original part from MTD, Ryobi, Yard Machines, Bolens, Yard Man, and Troy-Bilt for use in lawn tractors. The needle bearing attaches to the input shaft. You may need a wrench and a set of pliers when replacing this part. This item might break over time and will need replacing. It is made of metal and is sold individually.

This OEM 5 Pin ignition Switch is a silver, steel, individually sold part. It can be installed using a wrench and screwdriver, and has been rated as Easy to install. The part attaches to the dashboard, and is used to start and shut off the engine. If it is broken (likely due to fatigue), you will no longer be able to start or stop your ...Read moreengine and the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

This manufacturer-certified Hex Bolt, measuring 5/16-18 x .75 inch, is a gold, metal, individually sold bolt. It can be installed using a wrench or socket and torque wrench, by tightening to manufacturer specifications. If damaged (likely due to fatigue) the threads will be stripped, or the ends rounded off. If broken or missing, it sho...Read moreuld be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

The flat washer goes between the drive shaft and the flange bearing. It is an authentic OEM sourced item which is specially produced for use with lawn tractors and tillers made by MTD, Ryobi, Yard Machines, Troy-Bilt, Bolens, Yard Man, and Cub Cadet. This item is made of metal and is available as an individual replacement part. A wrench a...Read morend a set of pliers may be helpful when replacing this part. This washer may become broken and will need to be replaced.