21350PS (80S) Snapper Lawn Mower - Overview

The tine thatching spring or thatcher attachment spring tine for your lawn mower attaches to the spring alignment rod and pulls dead grass and roots to the surface. This part is black in color and is made of metal. It is an OEM part sourced directly from the manufacturer and is sold individually. Be sure to wear work gloves when you are replacing the tine thatching spring.

This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs. This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.

This driven ring is an OEM part direct from Snapper. The flexible plastic ring is compatible with many lawn mowers. This item is often fitted between the driven disc assembly and ring retaining plate, assisting the drive disc with propelling the mower. A screwdriver, wrench set, pliers are needed for the repair. This item is sold individually.

This is a original manufacturer sourced replacement part used on Snapper lawn mowers. This is the ground drive belt that connects the engine crankshaft pulley to the transmission pulley. This part is made out of rubber and it is sold individually. Clean the pulleys off before installing the new belt to ensure top performance and longevit...Read morey with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance. To replace this belt you would need a wrench and a screwdriver.

This replacement engine drive belt is a genuine Snapper item, not an aftermarket equivalent. It is supplied by original equipment manufacturer for use on lawn mowers. This belt helps to driver the mower. Over time belts tend to stretch and wear out requiring replacement. Please note, this rubber belt is sold individually. Replacing this drive belt will require a wrench set.

This is a genuine Snapper part. The axle bushing is constructed of high-quality metal, and is compatible with many lawn mower devices. This part helps to reinforce the front and rear wheel rims. Keep in mind this item is sold individually. A wrench and a screwdriver are needed in the removal and replacement.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

This replacement ball bearing is a commonly used on Snapper riding lawn mowers/tractors. It is supplied by original equipment manufacturer. Please check your models diagrams for correct location and application of this ball bearing. This is a sealed bearing which is sold individually. Ball bearings are designed to minimized friction between two rotating parts.

This is an authentic manufacturer-sourced component from Snapper. The clutch spring is designed to give enough pressure to the clutch, returning it to original position. This item is fitted onto the clutch idler arm and clutch control cable in the drive system. A screwdriver and a pair of pliers are helpful in making the repair. The metal clutch spring is sold individually.

This part is available as an individual replacement part and is made of plastic. The bushing goes between the worm shaft support bracket and the worm shaft. It will need to be replaced if it breaks. A set of pliers might be necessary during the installation of this item. This is a Snapper replacement part directly sourced from the manufacturer for use in snow throwers.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

It is an authentic part which is supplied directly from the original equipment manufacturer for use with Snapper lawn mowers. This is the handle that the clutch cable attaches to. It is made of durable metal and is sold individually. Note, the grip for the handle is sold separately. Make sure to check the appropriate diagrams of your mode...Read morel for the correct installation procedure. To perform this repair a screwdriver will be needed.