2107FK Makita Band Saw - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

Genuine Manufacturer Approved replacement Wheel Tire for some Makita Bandsaws. This part is made out of Rubber and is Sold Individually. When putting the tire on a band saw Wheel, it may seem too small but it is not. Band saw Tires will typically come approximately 2 or more inches smaller than the Tire you're replacing. The old Tire stre...Read moretches over time thus becoming less effective and eventually will break. Also, as Tire ages the rubber hardens and allows the Blade to slip. You would need to put the New Tire in Hot/Warm Water to heat the tire enough to make it pliable enough to stretch. Its preferred to use two people in the stretching process.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This replacement tapping screw is an authentic item that is supplied by the original manufacturer for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this part. This high-quality phillips pan-head screw is made of durable metal and it is sold individually.

This is a genuine manufacturer-sourced replacement bolt which is specially designed for use with Makita saws. It is a standard hardware which has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams of your unit for the correct location and use of this item. This high-quality hex socket head bolt is made of durable metal and it is sold individually.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

This is a genuine OEM sourced replacement tapping screw which is specially designed for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this item. This high-quality item is made of durable metal and it is sold individually.

This is a high quality item that is specially manufactured for use with Makita power tools. It is a standard hardware which has multiple used depending on the tool, please make sure to check appropriate diagrams for correct use and application of this screw. One durable metal pan head screw is included per order.

This part is an OEM from Makita. The stopper plate is compatible with many band saw models. This metal component is fastened to the gear housing, holding the project material in place for cutting. For the repair, you will need a hex key and a pair of pliers. The stopper plate is sold individually.

This is a Genuine OEM replacement part used on Makita Power Tools. This item is made out of Plastic and it is Sold Individually. The purpose of the Brush Cap is to retain the Brushes in the Brush Holders. This Brush Cap has external threads that thread into the housing of the tool. Be careful when removing and replacing these, they have a tendency to break.

This set of two carbon brushes is a genuine Makita replacement part, packaged in an official Makita retail box. Each brush includes wire leads and attached brush springs, and is designed to restore optimal performance in compatible Makita tools. Carbon brushes are among the most commonly replaced components in power tools, as they gradual...Read morely wear down through friction and regular use. Worn brushes can lead to intermittent motor function, reduced power, or diminished electric braking. Replacing them can resolve these issues and restore proper motor performance. Signs of wear include brushes worn near the wire lead, or those that are cracked, pitted, or burned. When replacing carbon brushes, it’s also important to inspect the armature for any signs of damage, such as burns or cracks, which may indicate a more serious motor issue.