20RJ746-H Hotpoint Range - Overview

Sections of the 20RJ746-H

[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Broil Element – Part Number: WB44X173
Broil Element
★★★★★
★★★★★
(24)
PartSelect #: PS249411
Manufacturer #: WB44X173
The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is brok...
$31.00
  In Stock
Oven Sensor – Part Number: WB21X158
Oven Sensor
PartSelect #: PS235718
Manufacturer #: WB21X158
This sensor offers 16 ohms of resistance at room temperature, though the resistance increases as the temperature increases.
  No Longer Available
Bake Element (16" long x 11-3/4" wide) – Part Number: WB44X169
Bake Element (16" long x 11-3/4" wide)
★★★★★
★★★★★
(1)
PartSelect #: PS249408
Manufacturer #: WB44X169
This closed hinged style bake element with screw in terminals is 16 inches long and 11-3/4 inches wide. Use it for your GE brand oven.
$104.29
  Special Order
DISCONTINUED – Part Number: WB24K2
DISCONTINUED
PartSelect #: PS236568
Manufacturer #: WB24K2
  No Longer Available
LATCH – Part Number: WB14X5035
LATCH
PartSelect #: PS231691
Manufacturer #: WB14X5035
  No Longer Available
DISCONTINUED – Part Number: WB22X5125
DISCONTINUED
PartSelect #: PS236262
Manufacturer #: WB22X5125
  No Longer Available
DISCONTINUED – Part Number: WB19X127
DISCONTINUED
PartSelect #: PS234013
Manufacturer #: WB19X127
  No Longer Available
DISCONTINUED – Part Number: WB10X98
DISCONTINUED
PartSelect #: PS686919
Manufacturer #: WB10X98
  No Longer Available

Questions And Answers for 20RJ746-H

Be the first to ask our experts a question about this model!

Common Symptoms of the 20RJ746-H

[Viewing 5 of 5]
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broiler Element Burned Out
Successful repair to Our GE range, manufactured prior to 1965 (when installed in house). Pulled range from wall, unplugged, removed burned-out broiler element. Previous check with GE to make cross reference of range part number to Part-select part number for this nearly 50-year-old range. Obtained new part and installed. Works. Range has self-cleaning oven, accidentally destroyed thermal switch attached to element mounting bracket, difficulty with frozen mounting nut. Self-cleaning still works; thermal switch locks out a solenoid which defeats door latch; prevents premature opening of oven door when oven too hot to open safely. Internet search did not find GE part but there are generic devices of the same type available; will consider installation later.
Parts Used:
Broil Element
  • Richard from Vestal, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench set
17 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven temperature too low
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.
Parts Used:
Oven Sensor
  • Ryan from Henderson, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
16 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not come up to temperature
Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the small wire nuts provided, then enlarged the hole in the oven wall, being careful not to pinch the wires then pushed the wire nuts and extra wire back through the hole and put the screws back in the flange.
Parts Used:
Oven Sensor
  • Clarence from Norwich, NY
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!