Models
>
20955
20955 Toro Lawn Mower - Overview
Models starting with 20955
Click on the best match to narrow your results.
- 20955 ( 315000001-315999999 ) Toro Lawn Mower (Toro Lawn Mower Model 20955/SERIAL: 315000001-315999999 (20955/SERIAL:315000001315999999, 20955/SERIAL: 315000001 315999999) Parts)
- 20955 ( 314000001-314999999 ) Toro Lawn Mower (Toro Lawn Mower Model 20955/SERIAL: 314000001-314999999 (20955/SERIAL:314000001314999999, 20955/SERIAL: 314000001 314999999) Parts)
- 20955 ( 313000001-313999999 ) Toro Lawn Mower (Toro Lawn Mower Model 20955/SERIAL: 313000001-313999999 (20955/SERIAL:313000001313999999, 20955/SERIAL: 313000001 313999999) Parts)
- 20955 ( 310000001-310999999 ) Toro Lawn Mower (55cm Recycler Lawn Mower, 2010)
- 20955 ( 311000001-311999999 ) Toro Lawn Mower (55cm Recycler Lawn Mower, 2011)
- 20955 ( 312000001-312999999 ) Toro Lawn Mower (55cm Recycler Lawn Mower, 2012)
- 20955 ( 316000001-316999999 ) Toro Lawn Mower (55cm Recycler Lawn Mower, 2016)
- 20955 ( 400000000-999999999 ) Toro Lawn Mower (55cm Recycler Lawn Mower)
- 20955 (400000000-402099999) Toro Lawn Mower (20955, 55cm Recycler Lawn Mower, (Sn 400000000-402099999))
- 20955 (402100000-404319999) Toro Lawn Mower (20955, 55cm Recycler Lawn Mower, (Sn 402100000-404319999))
- 20955 (404320000-999999999) Toro Lawn Mower (20955, 55cm Recycler Lawn Mower, (Sn 404320000-999999999))
Keep searches simple, eg. "belt" or "pump".
Washer-Stepped
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
In Stock
Bolt-Shoulder
PartSelect #: PS9046634
Manufacturer #: 614650
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket...
$4.99
In Stock
Nut-Lock, Ni
PartSelect #: PS9276436
Manufacturer #: 3296-29
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is use...
$3.99
In Stock
Ring-Retaining
PartSelect #: PS8950132
Manufacturer #: 32151-61
This metal retaining ring, otherwise known as a snap ring, holds parts in place in your lawn equipment, such as blades, shafts, pulleys, or other rotating components, to prevent them from sliding off ...
$3.99
In Stock
Belt-V
PartSelect #: PS8844898
Manufacturer #: 115-4669
Wheel drive belt. Width: 3/8 inch Length: 33 1/4 inch
$15.92
$27.40
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Parts Used:
-
randy from HIGHLAND, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
6 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!