2071 (1999-03) Jonsered Chainsaw - Overview

Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not part of a kit or assembly. The spark plug is used to ignite the air-fuel mixture inside the combustion chamber. You may need to replace the...Read more Spark Plug if your 1 cylinder engine won't start, or if your more-than-1 cylinder engine runs rough. Spark Plugs will wear over time and should be inspected regularly. Customers rate this repair as Easy.

This is a genuine manufacturer approved replacement part designed for use with chainsaws. It is used to secure starter housing to the unit. This is a metal phillips head screw which is sold individually.

This Nut is a genuine replacement part for hundreds of models of chainsaws. It is made of durable yellow plastic and is sold individually. This Nut is part of the chain tensioner and works with the tension screw to allow the user to tighten or loosen the chain. This part will become worn over time and should be replaced if you notice an...Read morey signs of wear or damage. If you cannot adjust the bar when you turn the tension nut/screw, it usually means that this Nut is worn or damaged. You will need a screwdriver, a socket set, and a wrench set to complete this repair. Customers rate this repair as Easy.

This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This is an authentic OEM sourced replacement part designed for use with Husqvarna chainsaws. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. To complete this repair you would need a screwdriver.

This authentic OEM rim sprocket in your chainsaw transfers power from the engine to the cutting chain. It is typically located at the center of the clutch drum, situated at the end of the engine crankshaft. By engaging with the chain drive links, it enables the chain to rotate and cut through materials as the engine turns. You will notice...Read more that if the rim sprocket is broken that the chain slips, does not engage, or rotates unevenly. It may also reveal signs of wear such as worn-out teeth. Failure to replace a broken rim sprocket can result in reduced cutting power, chain damage, and increased strain on the engine. To remove the rim sprocket, first, loosen the chain tension by adjusting the tensioning screw or knob. Then, remove the guide bar by loosening the nuts or clips on the side cover and sliding the guide bar off the saw. Use a screwdriver or appropriate tool to remove the screws or fasteners securing the clutch cover. With the clutch cover removed, you can access the clutch drum. Hold the drum in place and turn the retaining bolt counterclockwise to loosen it. Carefully slide off the clutch drum. This replacement part is sold individually.

This M8 flange nut secures the guide bar and chain assembly in place, ensuring proper alignment and safe operation of your equipment. Designed with an integrated flange and anti-slip teeth to resist loosening from vibration, it provides a reliable, secure hold during heavy use. Made from durable, corrosion-resistant steel with an M8 threa...Read mored and 1.25?mm pitch, replacing a worn or missing nut helps maintain stability and dependable performance.

This screw is an authentic OEM part which made for Husqvarna chainsaws. It is designed for multiple uses based on your tool. Please refer to diagrams for correct location and applied use of this screw. It includes one (1) metal screw per order. This is a hex head item so you would need a hex key/allen wrench to install or remove it.

This replacement screw is specially manufactured for Husqvarna power tools. It is a genuine OEM sourced hardware which has multiple applications depending on the model. Please make sure to check appropriate diagrams for correct use and location of this screw. Please note, this hex socket head screw is sold individually.

This is an original replacement part manufactured for use with trimmers. The start/stop switch is also called the kill switch, and fits on the upper handle above the throttle. The red switch is used to shut of the engine, and has to be engaged to run the engine. The switch is sold individually.

This is a genuine OEM part. The retaining ring is made for use with many chainsaws, and is used to help secure clutch drum components. The hardened metal component is sold individually. A hex key, screwdriver and pair of pliers are often required for the repair.

This is a genuine OEM supplied replacement hardware that is specially made for use with Husqvarna and Poulan chainsaws. It helps to distribute the pressure evenly between the connecting pieces, for correct location and use of this item make sure to check appropriate diagram of your model. This part is made from high quality metal and it is sold individually.