Models
>
20658
20658 Toro Lawn Mower - Overview
Models starting with 20658
Click on the best match to narrow your results.
Exact Part matches for your search term
[Viewing 5 of 5]
SPADE TERMINAL, FEMALE
This part number matches the current model number 20658
PartSelect #: PS2017327
Manufacturer #: 20658
No Longer Available
BAND
This part number matches the current model number 20658
PartSelect #: PS8692427
Manufacturer #: 00020658
No Longer Available
GASKET
This part number matches the current model number 20658
PartSelect #: PS8912658
Manufacturer #: 20658
No Longer Available
Lift Lever
This part number matches the current model number 20658
PartSelect #: PS11947196
Manufacturer #: 20658
No Longer Available
Guide-Belt Rev Pnt
This part number matches the current model number 20658
PartSelect #: PS16306092
Manufacturer #: 20658
No Longer Available
Keep searches simple, eg. "belt" or "pump".
Filter- A/C Cartridge
PartSelect #: PS8987387
Manufacturer #: 491588S
This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this...
$7.06
On Order
Plug-Spark
PartSelect #: PS9140427
Manufacturer #: 796112S
This part is the replacement spark plug for your engine. It measures approximately 2.5 inches by 1 inch. The spark plug creates the spark that ignites fuel in your engine during the combustion process...
$4.99
In Stock
Carburetor Overhaul Kit
PartSelect #: PS8984098
Manufacturer #: 498260
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of r...
$17.96
In Stock
Air Cleaner Gasket
PartSelect #: PS9138757
Manufacturer #: 795629
The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver...
$5.19
In Stock
Carburetor
PartSelect #: PS9139157
Manufacturer #: 799866
This is an authentic OEM replacement part used on lawn and garden engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. This Carburetor is a auto-choke system...
No Longer Available
Washer-Stepped
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
In Stock
Ring-Clip, Locking
PartSelect #: PS9052921
Manufacturer #: 65-2720
This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secure...
$3.99
In Stock
Spring-Compression
PartSelect #: PS8961286
Manufacturer #: 39-9650
This is a compression spring that is used within various models of lawn mowers and is used to provide stability and extra control to the user during the operation of the equipment. This spring works i...
$3.99
On Order
Common Symptoms of models starting with 20658
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torsion spring broken
I pryed the apart the torsion spring lever from the handle with a large screw driver. It wasn't easy putting it back, but it worked
Parts Used:
-
Henry from ORLAND PARK, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!