20643 Briggs and Stratton Engine - Overview

Authentic Manufacturer Sourced replacement part used on a variety of Engines. This rocker cover gasket is for the cylinder head. It is sold Individually. It provides a strong seal to protect from leaks. Over time gaskets tend to deteriorate and would need to be replaced.

The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will have a hard time engaging the fly wheel, making the engine harder to start, and should be replaced. Installation is rated as "Easy" by cust...Read moreomers, and will require a screwdriver, pliers and nutdriver. Refer to your make, model and diagram to ensure this is the correct part for you.This model is plastic and comes in white.

This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation, steady power output, and easier starting. Ideal for routine maintenance or replacement, it supports dependable engine performance in lawn and garden equipment, generators, and similar outdoor power machines.

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This manufacturer approved recoil starter pulley is designed for lawn and garden equipment engines. The recoil starter engages the drive cup on the flywheel to start the engine when pulled. This assembly includes: Plastic Pulley and a Metal Recoil Spring.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Metal, it is Sold Individually.

The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part. If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out. When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.

This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.

This genuine fuel tank assembly is sourced directly from the original equipment manufacturer and is specifically designed for use with Briggs & Stratton engines on lawn and garden equipment. It serves as the primary reservoir for storing fuel required by the engine. Constructed from durable plastic, this assembly includes both the fuel...Read more tank and cap. Note: Mounting hardware and fuel lines are sold separately. This tank features four mounting holes for secure installation. For proper fit and installation, refer to your equipment’s model diagram.