20500 - Overview

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This is a genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. The needle valve opens and closes to control the flow of fuel into the carburetor. It is made out of metal and it is sold individually. You would need a screwdriver and pliers to complete this repair.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This engine ring set is a genuine OEM replacement designed for small engine applications. It helps seal the cylinder properly to maintain compression, reduce oil consumption, and restore smooth, efficient engine operation. Ideal for engine rebuilds or repairs, this ring set should be replaced when wear causes power loss, excessive oil use, or reduced overall performance.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This is a genuine OEM lube fitting part made for use with various outdoor lawn equipment models and measures 3/16-inch wide. Sold as an individual part, this grease/lube fitting is made of metal and is used to deliver lubrication to whatever it is attached to for better performance, through a small passage in the fitting. If your lube fit...Read moreting needs to be replaced, it may require pliers and a hex wrench for that process. Check your user manual or any diagrams to make sure this is the correct part for your equipment.

This authentic component is specially designed for MTD riding lawn mowers and garden tractors. It is supplied directly from the original equipment manufacturer. The ball joint is an important part of the steering mechanism. Over time it may wear out or get damaged eventually requiring a replacement to keep your unit functioning properly. ...Read morePlease make sure to refer to the appropriate diagrams of your model for the correct application of this part. Keep in mind this high-quality ball joint is made of durable metal with a rubber component and is sold as an individual item. You need a screwdriver and a wrench set to take apart the housing and perform this repair.

This pair of keys is supplied by the equipment manufacturer for use in lawn and outdoor power equipment. The key is made of metal and designed to prevent unauthorized use or accidental starting of the equipment. It is fitted into the ignition switch, found near the operator seat or control panel. If the key is lost, damaged, corroded or w...Read moreorn down, you will not be able to engage and start the engine. These keys come in a set of two.

This is a genuine OEM sourced part which is specially designed for use with lawn and garden equipment. It is an identical replacement for a missing or a faulty bolt that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind t...Read morehis high-quality hex bolt is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.

This is a genuine OEM sourced replacement screw which is commonly utilized on MTD and Yard Machines lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. This durable metal hardware is sold individually.