2038 (Type 101) Black and Decker Electric Drill - Overview

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the...Read more new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.

Genuine Dewalt replacement part, this item is sold individually. The 696631-00 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly. In the Screw Drivers listed below this is the part that secures the Bit Holder in the spindle.

This synthetic gear grease is used to lubricate internal gears in power tools, reducing friction, wear, and noise during operation. Its high-performance formula helps prevent corrosion and protects moving parts under load. Applying fresh grease during maintenance restores smooth gear movement and extends tool life.

This genuine cord protector, also known as a strain relief boot, is designed to safeguard the power cord where it enters your tool housing. Made from flexible, durable material, it helps prevent the cord from bending, twisting, or fraying during regular use, supporting safe and reliable performance. Small but essential, this component is ...Read morean effective replacement if the original protector is worn or damaged, helping extend the life of your tool and maintain proper cord alignment.

Genuine OEM replacement part, this item is sold individually. This screw is used in various places in all of the tools listed below The most common use for this screw is to secure plastic housings together. It has a Torx T-20 head.

Includes part numbers 330003-04, 93128-00, 696631-00, 94518-00

Genuine DeWalt replacement part. rnIncludes 1 Carbon Brush with wire lead in rubber sheath attached.rnrn • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most...Read more commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with DeWALT and Black and Decker screwdrivers. This special component is utilized to provide an air-tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application...Read more of this hardware. Keep in mind over time the material may wear out and crack eventually requiring a replacement. It is a high-quality seal which is made of durable material is sold individually.

This is a genuine manufacturer-approved component which is designed for use with DeWALT and Black and Decker screwdrivers. The purpose of a spring is to apply tension on the guide in the clutch. Unfortunately, over time it may wear out, get damaged or simply lost eventually requiring a replacement. To ensure the exact location and the cor...Read morerect application of this hardware, refer to the diagrams of your model. One durable metal spring is included.

This is an original replacement part manufactured for use with electric power tools. The special sleeve is commonly used to provide spacing between the armature bearing and the motor housing. This sleeve is available as an individual replacement part, please see model diagram for associative parts.

This is an authentic Black & Decker replacement part. The terminal is designed by the manufacturer for use in drills, screwdrivers, and shears. This part is made of metal, and is used to create an electrical connection within the machine. You may require a screwdriver or Allen wrench and pliers when replacing this part. This item is sold individually. Included in part number 450562-00