2030N Makita Planer Jointer - Overview

This is an OEM part sourced directly from the manufacturer. The hex bolt is designed for use in Makita miter saws and planer-jointers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different bolts used in the machine. Refer to the parts diagram to b...Read moree sure of ordering the correct part. You will require a wrench when replacing this part. This item is sold individually.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This is an original replacement screw designed for use with Makita power tools. This is a standard hardware which has multiple uses based on equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 16 Gauge • 8 Feet Long

This cord guard / strain reliever is a genuine Makita replacement part. It covers the final portion of cord before entering the tool, providing extra rigidness and preventing cord damage. Over time these cord guards break down and require replacement. The guard is constructed of heavy duty rubber compound for toughness. This cord guar...Read mored is compatible with the tools listed below. It is not guaranteed to fit any other power tool models.

This is a genuine OEM sourced component which is specially made for use with Makita saws. It provides an identical replacement for a missing or a faulty hex wrench that was included with a new unit. The part allows a user to secure or remove hex socket head hardware. Please make sure to refer to the owners manual and the appropriate diagr...Read moreams of your model for the correct location and application of this part. Keep in mind this high-quality hex wrench is made of durable metal and is sold individually.

This genuine OEM woodruff key is a small, semicircular metal piece used in various power tools to connect rotating parts, such as shafts or gears, to other components like wheels or pulleys. It prevents slippage between these parts, ensuring smooth synchronization and power transmission. With a width of 3/32 inches and a length of 5/8 inc...Read morehes, consider replacing a woodruff key if you notice misalignment or excessive movement between the connected parts. Be sure to inspect the key for signs of wear, damage, or bending. Removing the key depends on the make and model of your tool. If the key is visible, gently tap it from one side using a small hammer and a punch or drift pin. This will dislodge it from its slot. If the key is stuck or difficult to access, you may need to partially disassemble the tool to gain better access to the key. Once the key is loose, carefully pull it out using pliers. Clean the keyway and slot before installing the new key. Before making your purchase, remember that this component is sold individually.

This fifteen (15) pin sprocket is an authentic part made by original manufacturer. It is compatible with some Makita planers/planer-jointers. A sprocket engages and drives a chain and/or gear. This item is sold individually.

Genuine Makita replacement part. This phillips pan-head screw includes a washer. It is sold individually.