2012 Makita Planer Jointer - Overview

This is an Authentic OEM Approved replacement part designed for use with Makita Planers/Jointers. This part is made out of Metal and it is Sold Separately. This part helps to secure the Roller and allows it to spin smoothly. To replace this part you would need Retaining Ring Pliers, Screwdriver and a Set of Wrenches.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This is an original replacement screw designed for use with Makita power tools. This is a standard hardware which has multiple uses based on equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 16 Gauge • 8 Feet Long

This is an authentic replacement part manufactured for use with Makita miter saws, drills, and planers. Wave washers are commonly used to provide spacing between parts and to deflect pressure between parts. The wave washer is sold individually.

This genuine OEM woodruff key is a small, semicircular metal piece used in various power tools to connect rotating parts, such as shafts or gears, to other components like wheels or pulleys. It prevents slippage between these parts, ensuring smooth synchronization and power transmission. With a width of 3/32 inches and a length of 5/8 inc...Read morehes, consider replacing a woodruff key if you notice misalignment or excessive movement between the connected parts. Be sure to inspect the key for signs of wear, damage, or bending. Removing the key depends on the make and model of your tool. If the key is visible, gently tap it from one side using a small hammer and a punch or drift pin. This will dislodge it from its slot. If the key is stuck or difficult to access, you may need to partially disassemble the tool to gain better access to the key. Once the key is loose, carefully pull it out using pliers. Clean the keyway and slot before installing the new key. Before making your purchase, remember that this component is sold individually.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This is an original Makita replacement part manufactured for use with planers. This drive belt is used to drive the blade drum. Belts can wear out over time from constant motion, and replacing a worn belt is part of normal planer maintenance. This belt is sold individually.

The compression spring connects to the pin. It is made of metal and is sold individually. This is an OEM part sourced directly from the manufacturer and used in Makita saws. A set of pliers might be necessary during the installation of this item. This part will need to be replaced if it breaks or bends.

It is a genuine item which is supplied by the original equipment manufacturer for use with Makita planers. This is an identical replacement for a missing or faulty torsion spring that was installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Kee...Read morep in mind this high-quality spring is made of durable metal and is sold individually.

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Y...Read moreour model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.