20092 Toro Lawn Mower - Overview

This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this can lead to reduced performance. This air filter is approximately 4 inches wide and approximately 5 inches long. To replace the air filter,...Read more locate the air filter cover on the side of the engine, unscrew it, and remove the old filter. Be sure to clear out any dirt, clippings, or other debris that has found its way into the air filter assembly before you insert the new filter. Reattach the air filter cover, and secure it with the screws. This product is sold individually.

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of reasons. When your carb becomes clogged, it is often a good idea to take it apart and replace the various parts inside by purchasing a carbur...Read moreetor kit. This is a 15-piece set and contains everything that you will need to do a total overhaul of your carburetor. You may want to purchase some carb cleaner as well, to ensure that the new pieces in the carb kit fit and adhere properly.

The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver, pliers, socket set, and nut driver. It attaches between the base of the air cleaner assembly and carburetor. If broken, damaged or worn do...Read morewn it will allow dirt to enter the carburetor, causing performance issues. If this happens, replace it. Refer to your make, model and diagrams to check if this is the right part.

This genuine OEM engine gasket set is sourced directly from the manufacturer and includes the gaskets needed to seal the components in a gas-powered engine. This set ensures proper fit and performance to maintain the life of your lawn equipment engine. When installing replacement gaskets, make sure to wear work gloves to protect your hands.

This is an authentic OEM replacement part used on lawn and garden engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. This Carburetor is a auto-choke system. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspo...Read moreon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This assembly includes a metal body carburetor, rubber o-ring and a gasket. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This is a manufacturer approved replacement part designed for use with a variety of lawn and garden engines. The air vane spring maintains the proper tension on the air vane choking system. If it is broken, it can cause the engine to not start. To replace it you will need pliers.

This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

This genuine replacement magneto is designed for Briggs & Stratton engines used in Toro lawn mowers. It plays a vital role in the ignition system by generating the electrical current needed to fire the spark plug. Made from high-quality materials, this part is sold individually. Note: The spark plug boot is sold separately. To replace...Read more the magneto, begin by removing the housing or covers from your mower. Next, remove the spark plug and bind the cylinder to prevent it from turning. Disconnect the ignition wires and remove the old ignition coil. Install the new magneto, carefully setting the correct air gap between the coil and the flywheel. Once installed, reassemble the unit and test for proper operation. A screwdriver set is recommended for this repair.

This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.

This is a genuine OEM approved shoulder bolt designed for use with Toro walk behild/push lawn mowers. The common purpose for this shoulder bolt is to secure the handle to the mounting blacked of a mower. This hex head bolt is sold individually. Please make sure to use only properly sized wrench when installing or removing this bolt.