This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this can lead to reduced performance. This air filter is approximately 4 inches wide and approximately 5 inches long. To replace the air filter,...Read more locate the air filter cover on the side of the engine, unscrew it, and remove the old filter. Be sure to clear out any dirt, clippings, or other debris that has found its way into the air filter assembly before you insert the new filter. Reattach the air filter cover, and secure it with the screws. This product is sold individually.
This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of reasons. When your carb becomes clogged, it is often a good idea to take it apart and replace the various parts inside by purchasing a carbur...Read moreetor kit. This is a 15-piece set and contains everything that you will need to do a total overhaul of your carburetor. You may want to purchase some carb cleaner as well, to ensure that the new pieces in the carb kit fit and adhere properly.
The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver, pliers, socket set, and nut driver. It attaches between the base of the air cleaner assembly and carburetor. If broken, damaged or worn do...Read morewn it will allow dirt to enter the carburetor, causing performance issues. If this happens, replace it. Refer to your make, model and diagrams to check if this is the right part.
This genuine OEM engine gasket set is sourced directly from the manufacturer and includes the gaskets needed to seal the components in a gas-powered engine. This set ensures proper fit and performance to maintain the life of your lawn equipment engine. When installing replacement gaskets, make sure to wear work gloves to protect your hands.
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. Installation is rated as "Easy" by customers and will require a socket set. This part is individually sold, gray, and constructed of metal. R...Read moreefer to your make, model and diagrams to check if this is the right part for you.
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. You can use this blade with the Recycler Cutting System to chop grass clippings into fine mulch particles and return them to the ground.
This is an authentic OEM replacement part used on lawn and garden engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. This Carburetor is a auto-choke system.
If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspo...Read moreon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem.
This assembly includes a metal body carburetor, rubber o-ring and a gasket. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.
This is a manufacturer approved replacement part designed for use with a variety of lawn and garden engines. The air vane spring maintains the proper tension on the air vane choking system. If it is broken, it can cause the engine to not start. To replace it you will need pliers.
This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.
This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket and is rated as "Easy" by customers. It is mostly used to keep the wheel in place. It fits onto the unit frame and if broken or removed, th...Read moree wheel will fall off. Refer to your make, model and diagram to ensure this is the correct part.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leaking gaskets
4 of 10 peoplefound this instruction helpful.
Dustin from BANGOR, ME
A Bit Difficult
More than 2 hours
Socket set, Wrench set
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
Was this helpful?
Thank you for voting!
Torsion spring broken
3 of 11 peoplefound this instruction helpful.
Henry from ORLAND PARK, IL
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers
I pryed the apart the torsion spring lever from the handle with a large screw driver. It wasn't easy putting it back, but it worked
Was this helpful?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
7 of 25 peoplefound this instruction helpful.
Ray from YARDLEY, PA
Really Easy
Less than 15 mins
Socket set, Wrench set
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket. Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck. Position new spring arm over the slot on wheel height
... Read more assembly plate. Check opposite side to verify correct orientation if needed. Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever. Replace wheel height assembly. Replace wheel.