My Orders
20039 Toro Lawn Mower - Overview
Models starting with 20039
Click on the best match to narrow your results.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$6.40
In Stock
Starter Pawl-Ratchet
Part #281505S
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will have a hard time engaging the fly wheel, making the engine harder to start, and should be replaced. Installation is rated as "Easy" by cust...Read moreomers, and will require a screwdriver, pliers and nutdriver. Refer to your make, model and diagram to ensure this is the correct part for you.This model is plastic and comes in white.
Read less
No Longer Available
Bowl-float
Part #796611
This item is an authentic replacement part that has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The metal float bowl fits onto the bottom of the carburetor and is used to house the float and store and drain the fuel that actuates the needle valve. This item is available as an individual replacement part.
$6.40
In Stock
Key-flywheel
Part #222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.
$6.40
In Stock
Retaining Ring
Part #65-2720
This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.
$7.47
In Stock
Seal-oil
Part #299819S
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.
Read less
$17.73
In Stock
Filter-a/c Cartridge
Part #697029
This replacement part is designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to filter out dust and debris from contaminating engine and carburetor. This cartridge will get dirty over time requiring replacement. This is a pleated paper filter with a plastic base/frame. Includes one (1) filt...Read moreer cartridge per order. Please note foam filter is sold separately. Replacing air filter is easy and does not require any tools. • First remove the knob • Remove cover and take out old air filter • Clean out the filter base/housing • Place new air filter in the case • Reassemble and test the engine
Read less
$78.26
In Stock
Engine Fuel Tank
Part #699374
This fuel tank is for lawn and garden equipment engines.
Fuel tank holds the gas that's needed by the engine.
Work in a well-ventilated area when installing this part. Drain the existing fuel from the tank and disconnect the spark plug wire before beginning the repair.
$23.05
In Stock
V-belt
Part #91-2258
Genuine Toro V-Belt used on Lawn Mowers, it is sold individually. This is the Drive Belt that connects the Transmission and the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.
$5.95
In Stock
Screw-handle
Part #92-2260
Genuine OEM sourced part used on variety of Toro Lawn and Garden Equipment. This part is sold individually and the Nut is not included. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the bolt and keeps it from turning when the nut is tightened.
$7.19
In Stock
Knob-handle
Part #106-4161
Genuine OEM replacement part used on Walk Behind Mowers and Snowblowers. This is a Plastic Knob with a Metal Bushing inside. Does not ship with screw or washer these parts are sold separately. Replacing this part is very easy and it does not require any additional tools.
$6.57
In Stock
Filter-a/c Foam
Part #273356S
This is an OEM sourced replacement part used on Briggs and Stratton and Toro equipment. Its purpose is to provide an extra layer of protection from dust and other contaminants. One foam air cleaner filter is included per order. Please note, the main pleated paper filter is sold separately. Depending on your equipment you may need a scre...Read morewdriver to replace this filter. • Remove the cover • Take out the old filter • Secure the new filter in place • Reattach the filter cover
Read less
$6.40
In Stock
Screw
Part #691108
This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.
Exact Part matches for your search term
No Longer Available
No Longer Available
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The hub that the mower blade mounts to was broken
8 of 26 people
found this instruction helpful.
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Other Parts Used:
Was this helpful?
Thank you for voting!