2000FA Shimano Spinning Reels - Overview

This spool washer is a genuine OEM part. The Shimano washer is compatible with many spinning reels. This hardened metal item is fitted in the spool assembly, securing the main shaft. The washer is sold individually, and a screwdriver is needed for making the replacement.

This genuine manufacturer-supplied spacer is specially designed for Shimano fishing reels. It helps to provide spacing and a tight seal for the line roller. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. Refer to the appropriate diagrams for your model to ensure the proper repair procedur...Read moree. One durable spacer is included. A screwdriver will be needed to take apart and reassemble the reel when replacing this component.

It is an authentic OEM sourced item which is specially produced for use with Shimano reels. The crosshead screw connects to the right side plate and is made of metal. This is a very small part that will need to be replaced if it gets lost or stripped. A Phillips screwdriver is needed to replace the screw. This is available as an individual replacement part even though many might be needed.

This is an authentic Shimano replacement part that is sourced from the original manufacturer for use with reels. The bail arm click attaches to the click spring and is made of metal. During replacement, it may require a screwdriver to help install this item correctly. It may become lost or broken and will need to be replaced. This is available as an individual replacement part.

This authentic part is supplied by the original equipment manufacturer for use with Shimano fishing reels. The spring applies tension on the connected parts. Unfortunately, over time it will wear out and it may begin to stretch eventually requiring a replacement. This high-quality spring is made of durable metal and is sold as an individu...Read moreal item. Check the diagrams for your model to ensure the proper repair procedure. A screwdriver might be needed to replace this anti-reverse cam spring.

This is a Genuine Manufacturer Sourced replacement part used on Shimano Spinning Reels. This part is made out of Metal and it is Sold Individually. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces...Read more friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. To replace this Bearing you would need a Screwdriver. First you would need to disconnect the Reel Handle. Then remove the Side Cover by loosening the Screws that hold it. You should be able to remove the old Bearing. Install new Bearing and Reassemble the Reel

This authentic manufacturer-supplied washer is specially made for use with Shimano fishing reels. It is a special hardware that helps to provide a tight seal between connected components. This is an identical replacement for a missing or a worn washer that was installed on a new unit. One durable metal part is included. Refer to the appro...Read morepriate diagrams for your model to ensure the proper repair procedure. A screwdriver might be needed to replace this hardware.

This part is made of metal and is available individually. The spool support attaches to the main shaft. A screwdriver may be helpful when replacing this item. It will need to be replaced if it becomes broken. This is an OEM Shimano part directly sourced from the manufacturer for use reels.

This authentic OEM washer in your spinning reel is positioned next to the drive gear, which is responsible for turning the spool and controlling the line retrieval. It can be found within the body and side cover of the reel. The washer acts as a cushion, reducing friction and ensuring smooth operation of the reel. Over time, the washer ca...Read moren become worn, damaged, or corroded. Signs that it needs to be replaced include increased noise, decreased smoothness in reel operation, or if the drive gear shows excessive wobbling or play. To remove the existing washer, you need pliers and a screwdriver. Follow the steps in your user manual to remove the spool, rotor, anti-reverse assembly, pinion bearing, and drive gear. Once removed, replace the drive gear and bearing with the new washer, then reassemble the reel in the reverse order.